3MillID 3M Mullion Installation Manual - Page 2

Browse online or download pdf Installation Manual for IP Access Controllers 3MillID 3M Mullion. 3MillID 3M Mullion 2 pages.

Print Page
These notes are provided as a general guidance for mounting, fixing and connecting 3millID - 3M series RFID
readers. Please consult your installer and the manufacturer' s details of your control panel, when configuring
your access security system.
1
If fitted, remove reader module
securing screw.
Position the reader module, ensuring
5
the top-edge fixing lugs engage
correctly with the recesses located at
the top of the backplate.
These devices comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
2AKUW-AV00
received, including interference that may cause
2AKUW-AV90
undesired operation.
Any changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate the equipment.
FCC ID: TCZ-10103751G1
These devices contains:
EQUIPMENT
BP21018
Pull bottom edge of reader module
2
away from the backplate, and lift up.
Swing the bottom edge of the module
6
down and forward until you feel the unit
click shut.
Together
with
information
provided
by
suppliers and subcontractors, these devices
R o H S
comply with the requirements and relevant
c o m p l i a n t
provisions of:
EU Directive 2011/65/EC.
These RFID proximity readers comply with
the essential requirements and relevant
provisions of:
EU Directive 2014/53/EC
1
GENERAL GUIDANCE NOTES
Mount the reader backplate to a flat
3
surface using suitable hardware having a
diameter no greater than 0.15 in (4mm).
Secure the reader module to the
7
backplate using the M3x100mm screw
as supplied.
If required, you may opt to
use security screw.
This symbol on the product or on its packaging
indicates that the product must not be disposed of
with normal household waste. Instead, it is your
responsibility to dispose of your waste equipment
by arranging to return it to a designated collection
point for the recycling of waste electrical and
electronic equipment. By separating and recycling
your waste equipment at the time of disposal you
will help to conserve natural resources and ensure
that the equipment is recycled in a manner that
protects human health and the environment.
EU Directive 2012/19/EU
7
to
APPLIES TO ALL READER MODELS LISTED OVERLEAF
Once the backplate has been mounted, make wire connections to
4
the reader module in accordance with the screw terminal
connections shown below, and your control panel requirements.
Ensure the cable does not impair or prevent the reader module
being secured.
1
-
0V
Supply voltage ground
2
-
+Vdc
Supply voltage (+10Vdc to +16Vdc)
3
-
DATA1/CLK
Wiegand or Clock/Data output
4
-
DATA0/DAT
Wiegand or Clock/Data output
5
-
GREEN
Green LED control input
6
-
RED
Red LED control input
7
-
Buzzer
Buzzer control input
8
-
TMPR/CP
Tamper or Card Present output
9
-
RS485-
RS485 Bus
10
-
RS485+
RS485 Bus
Applicable to 3M Inline add-on reader only. The following is a
4b
diagrammatic representation of the wiring configuration providing a
Bluetooth capabaility to most existing installations. Please consult
your installer and the manufacturer' s details of your existing control
panel and access control reader.
( THIS CONFIGURATION NOT EVALUATED BY UL )
pin
line IN
1
0V
2
+Vdc (+12Vdc)
3
N/A
4
N/A
5
N/A
6
N/A
7
N/A
8
N/A
9
RS485 -
10
RS485 +
line in from control panel
security
access
CONTROL
PANEL
line OUT
0V
+Vdc (+12Vdc)
N/A
N/A
N/A
N/A
N/A
N/A
RS485 -
RS485 +
line IN
line OUT
existing
ACCESS
CONTROL
READER