DSE RE-BCC8FD Owner's Manual - Page 2
Browse online or download pdf Owner's Manual for Security Camera DSE RE-BCC8FD. DSE RE-BCC8FD 3 pages.
Print Page
OWNER'S MANUAL
illumination power and the OSD configuration menu. To
send the commands you can use a PTZ console or our
DVR that has RS485 port.
The two terminals of the RS485 port are connected with a
twisted pair to the control mechanism, respecting the
order A + / B- without swap them.
To send commands using the following settings:
PROTOCOL PELCO P / D
ADDRESS 1
SPEED '9600
you can not change
TARGET
Adjust zoom / focus - The camera is equipped with a
manual lens adjustable from 5 to 50 mm.
Once the camera is positioned it is necessary to adjust the
zoom and the focus of the lens by acting on the two
adjustment rings
Acting initially on ZOOM (most advanced ring) and adjust
the amplitude of the frame (wide angle / zoom) based on
the area to be framed. Remember that in most wide angle
corresponds inevitably less image detail.
Generally, it is good to fit a narrower width as possible
around the location where it will lie in the plate, so that
the same appears as large as possible in the frame.
Once defined the field of view act on FOCUS adjustment
(rearmost ring) to focus perfectly framed area. Recall that
each lens has its own depth of field to which it is possible
to put in focus in a perfect way only a portion of the space
in front of the camera. Concentrate on the most important
area where you will find the plate of the vehicle to adjust
the focus optimally.
It may be helpful for an optimal adjustment to position a
car stops at the exact point where it carries out the
reading of the license plate.
The objective also has a central ring for the aperture
(OPEN / CLOSE) which should be left in the full open
position.
IR LIGHT
The camera incorporates an internal infrared illuminator
that emits illumination invisible to the human eye, but
visible tothe camera. L'Illuminator turns itself on when it
gets dark and the camera switches alone in night vision
mode. The illuminator ignition allows the vision of
absolute darkness plate until its flow rate of 30 meters
illumination.
Note that in this camera, the illuminator is used for the
vision of the automobile license plate and does not allow,
if not marginally, the night vision of the medium or
environment. If this is required it must be the coaching of
another conventional camera.
IR brightness adjustment- E 'can adjust the brightness
of the illuminator to adapt to the distance of the shot. If
the plaque comes too close, within 10 m. for example,
agree to reduce the brightness to avoid that is too
bleached.
To properly adjust the lighting going into a real and
illuminators dark conditions lit by placing a retainer means
in the license plate reading point. If the license plate is
bleached with unreadable characters must reduce the
power of the LEDs. Acting on the adjustment so as to
optimize the illumination on the plate.
RE-BCC8FD camera license plate
DSE srl - Digital Surveillance Equipment - WWW.DSE.EU
The power of the LEDs is adjusted with the button on the
camera cable or it is also possible remotely via RS485
serial port (see below).
Adjusting the IR LED power- Using the up and down
button increases and decreases the brightness of the
LEDs. The camera does not have indicators that show the
power of the LEDs selected, as this is physically visible on
the degree of power illuminator.
Once you reached the desired level must press the button
in a central location to store the power selected so that it
will be maintained in the event of mains failure.
BUTTON ON BOARD ROOM AND OSD MENU
On the electronic card there is a button that allows access
to the OSD less of the camera.
In this there are many settings menu. Care should be
taken that four of these are essential to enable the
reading of the day and night plaques.
LENS - This setting should be kept to MANUAL, having
these cameras a manual lens.
EXPOSURE / SHUTTER - This setting is factory value
1/400 and it is possible to maintain this value unchanged
until the speed of the means
less than 100 Km / h. If the means traveling at speeds
top is good to set a faster shutter as 1/1000 and beyond.
More it provides for the high speed of the medium to
resume more it will take a short amount of electronic
shutter time. However most it will shorten the shutter
time as it reduces the overall brightness of the night
video.
For this reason, if you anticipate lens means, as in the
case of driveways, it is also possible to lengthen the
shutter time of 1/200 to obtain a brighter image night.
The maximum speed of the means to resume can not
exceed 180 km / h.
EXPOSURE / AGC- This setting is factory preset to an
average value (6). You can increase the AGC to increase
nocturnal brightness, even in the face of most video
noise.
DAY & NIGHT - This setting should be kept to EXT so
that the happend / night passage is decided by the
external sensor of brightness.
Document: RE-BCC8FD 2C0
Page: 2