Attacus AT-800 Quick Start Manual
Browse online or download pdf Quick Start Manual for Treadmill Attacus AT-800. Attacus AT-800 3 pages.
Print Page
AT800 Specifica on
Basic speci fca on
Unit dimensions:
Length: 200 CM (78.74 in)
Width: 89 CM (35.04 in)
Height: 135 CM (53.15 in)
Unit weight:
123.5 KG (272.3 lb)
Maximum weight
150 KG (330.7 lb)
carrying capacity:
Belt size:
51 x 150 CM (20 x 60 in)
Motor:
2.5 HP
Voltage:
110V
220V，50/60Hz
Speed:
0.8~20 (KM/HR)
Incline:
10 %
Basic equipment
Hand held heart
YES
rate monitor:
Wireless receiving
5 kHz, Bluetooth and ANT+
device:
Fan:
YES
Audio:
Bluetooth audio device/High
quality audio
Fan
Magazine rack
Rack
Func on panel
Power switch/power cord
Upright
Upright safety cover
Hydraulic li system
Rou ne Maintenance
Keep the treadmill and surroundings clean can effec vely decrease maintenance issues. We recommend
users to abide by following preven ve maintenance procedure. Please make sure the power of treadmill
is off and the power cord is unplugged for any maintenance.
Daily maintenance
1) Please wipe the treadmill, motor safety guard, console and display console set with clean cloth. DO NOT use any detergent.
2) Check if the power cord is damaged. Please contact the distributor or Alatech customer service for any damage.
3) Make sure the power cord is not pressed by the machine or jammed anywhere.
4) Check if there is any stain that can affect opera on on the belt.
5) Check belt tension. Make sure the uncalibrated belt will not damage other components.
Weekly maintenance
1) Upright the treadmill and check if the pin of hydraulic li can be securely locked.
2) Move the machine and clean the dust and stain underneath the treadmill. Move the machine back a er cleaning.
Monthly maintenance
1) Make sure all screws are securely locked.
2) Upright the treadmill and check if there is any loose or missing component.
Yearly maintenance
1) Please lubricate the pin of hydraulic li , the sha of iron pieces, deck and belt every year to ensure normal opera on.
Please make sure the power of treadmill is off and the power cord is unplugged for any maintenance. Please contact the distributor or
Alatech customer service for any maintenance issue.
Grounding Instruc on
Grounding
The power socket of this product contains a grounding conductor. This socket must be inserted into the outlet via the power cord with grounding latch. The plug must
be plugged into an appropriate outlet that is properly installed and grounded in accordance with local codes and ordinances.
Outlet
This product uses a rated voltage of 220V or 110V and comes with a three-pin power cord as shown in the following illustra on.
If the grounding outlet is not available, please use grounding adapter to connect this plug to the two-pin outlet. Please have qualified electrician install the
grounding outlet correctly before using the adapter. Please connect the grip or similar adapter extension to the ground and fix with the metal screw whenever
the adapter is used. Refer to the following illustra on.
Do determine the power cord is electrically related for 220V or 110V by checking the specifica on label or specifica on. Please make sure
the cord is connected to the plug with correct voltage. DO not use the power cord via adapter or extension cord to avoid of any component damage or personnel
injury caused by sudden voltage changes such as voltage surges and spikes.
Power cable
Three-pin outlet
•
The above illustra ons only show three-pin power code power cord and outlet or two-pin outlet and grounding adapter. The type of
three-prong, two-prong and grounding adapter may vary in different countries. The enclosed power cord will be provided according to local
regula ons of each country..
Make sure the power cord is connected to the outlet with correct voltage. DO NOT connect the power cord to the outlet via voltage adapter
•
or extension cord to avoid accidental current that may damage component and lead to personnel injury.
Exercise programs
P0
MANUAL
P1
INTERVAL 1-1
P2
INTERVAL 1-2
P3
INTERVAL 1-3
P4
WEIGHT LOSS
P5
HILL CLIMB
P6
CROSS COUNTRY
P7
DISTANCE GOAL
P8
STEP GOAL
H1
BASIC HRC 60%
H2
BASIC HRC 80%
U1
USER 1
U2
USER 2
Water bo le holder
Handrail quick key
Console display overview/opera ng panel
Heart rate sensor bar
Motor safety guard
Belt tension adjus ng screw
Two-pin outlet
Power cable
Metal grounding screw
Grounding adapter
Before Assembly
No ces and safety ps
Enclosed tools
1) Please move and transport the treadmill carefully. Put the box on a level surface. Only open the box with its
Hex wrench
surface on top. It is recommended to put a protec ve mat on the floor.
Phillips screwdriver
2) Unpack and assemble the treadmill at the planned loca on to avoid unnecessary transporta on. Pay great
a en on when unfastening cable e that used for packing or fixing to avoid accidental bounce.
Assembly parts
3) Please follow assembly procedure to assemble the treadmill a er unfastening cable e. Please fold the machine
to upright and make sure the pin of hydraulic li
Console x 1
crane the machine.
Display Console x 1
4) DO NOT try to li or move the machine with a single part or stand. (Refer to "Move/transport the treadmill" on
P.14 for informa on related to moving the product.)
Upright x 2(L & R)
Upright safety cover x 2(L & R)
Accessory pack
•
Hardware parts box x 1
Safety key x 1
•
Power cable x 1
Line-level audio adapter x 1
•
Silicon oil x 1
Please contact the distribu-
tor or the Warranty card for
•
technical support if any part
•
is missing or you have any
ques on.
Speaker
Step 1 of Assembly Procedure
Handrail
Console cable
Safety key
B
Side rail
B
C
C
C
Belt
D
A
C
D
A
Hex wrench
Caster
• Put the console strut on the frame with great care to avoid any damage to the console cable.
• DO NOT lock the screw ghtly before you finish step 3.
Step 2 of Assembly Procedure
Step 3 of Assembly Procedure
C
A
C
A
A
C
B
A
C
B
D
A
D
A
B
• Please assemble the display console with great care. Make sure no wire is pressed or bent to avoid any damage.
• Make sure all screws are well posi oned and lightly locked. DO NOT lock the screw ghtly when posi oning to ensure a smooth assembly.
is securely locked if you need to li or move it. DO NOT try to
When assembling, make sure all nuts, screws and parts are posi oned and lightly locked before
proceeding to the next step. A er the assembly is completed, make sure all screws are securely
locked. DO NOT arbitrarily decrease the quan ty of assembling screw.
Several parts are lubricated before delivery to facilitate assembly. DO NOT arbitrarily wipe off the
lubricant. You can use lubricant to assemble parts when facing any difficulty. It is recommended
to use the lithium base grease for bike.
Several parts are very heavy; DO NOT try to assemble the machine on your own. These heavy
parts may fall and lead to personnal injury. Strongly recommend to have more than 2 persons for
assembly.
Please follow assembly instruc ons to li or move the treadmill. DO NOT arbitrarily li or take out
the product from the package.
Fail to following above instruc ons may lead to personnal injury and machine damage. Please
pay great a en on to these instruc ons.
Parts
Illustra on
A
B
C
D
B
C
1) Open hardware pack 1.
A
D
2) Connect the lead wire to the console cable, pull them through the
B
C
A
C
right upright of the console, pull out the lead wire from the right upright
D
C
and then fix the console cable to the top of upright. Please remove the
lead wire then.
3) Put the right upright on the frame.
4) Use part A, C & D (2 of each) and connect the upright to the frame.
Make sure all screws and washers are well posi oned and lock them
lightly.
5) Use part B & C (2 of each) and connect the upright to the frame. Make
sure part B & C are well posi oned and lightly locked. Confirm all screws
and washers on the right side are posi oned.
6) Repeat step 3~5 to complete the assembly of the le upright.
1) Take the le and right upright safety covers.
2) Put the protec ve cover through the right upright safety cover carefully.
3) Put the protec ve cover through the le upright safety cover carefully.
Hardware pack for step 3
Parts
Illustra on
A
B
C
Console connec ng cable
D
1) Open hardware pack 3.
Console cable
2) Connect the console cable to the connec ng cable on the console.
D
A
D
A
3) Put the console on the uprights carefully.
Hex wrench
4) Use part A & C (2 of each for le and right side), connect the upright
to the frame. Make sure all screws and washers are well posi oned and
lock them lightly.
Phillips screwdriver
5) Use part A & D (2 of each for le and right side), connect the upright
B
to the frame. Make sure all screws and washers are well posi oned and
lock them lightly.
6) Li the uprights safety cover of the upright on both sides and lock all
screws at the lower side of upright ghtly.
7) Use part B (2pcs for le and right side) and lock the uprights safety
cover of the upright safety cover on both sides ghtly.
8) Lock all screws ghtly.
Hardware pack for step 1
Type
Descrip on
Qty
Screw
Bu on Head Socket Bolt (55L)
4
Screw
Bu on Head Socket Bolt (20L)
4
Washer
Flat washer (Ø23)
8
Washer
Split washer (Ø18)
4
Type
Descrip on
Qty
Screw
Bu on Head Socket Bolt (20L)
8
Screw
Truss head Phillips screw (10L)
4
Washer
Flat washer (Ø23)
4
Washer
Curved washer (Ø23)
4