Attwood 69212T Installation Instructions

Browse online or download pdf Installation Instructions for Boating Equipment Attwood 69212T. Attwood 69212T 2 pages. Attwood ski mirror installation instructions

Print Page

Ski Mirror

9083

Installation Instructions

SAVE THESE INSTRUCTIONS

Form Number 69212T Rev. B

FEATURES

The Attwood Ski Mirror is designed with a universal mount which

allows mounting on either the dash or windshield extrusion (up to

3/4" thick). It adjusts freely to any position, any angle, up or down

or side to side.

The design includes a shatterproof convex lens that eliminates blind

spots. It is compact and lightweight.

The spring-loaded ball joint holds mirror firm to prevent vibrating out

of position.

Also features gleaming ZAMAK with Perma-Plate

DASH-MOUNTED SKI MIRROR

Tools and Materials Required for Installation

1. Drill and drill bits.

2. Two #10 x 3/4" stainless steel wood/sheet metal pan-head screws

(not included).

3. Phillips Head screwdriver.

INSTALLATION INSTRUCTIONS

1. Select a desirable location at or near centerline of the boat, making

sure there is enough room to work before drilling. (Figure 1)

Figure 1

Adjust

Tighten

Screws

Center of Dash

2. Mark the hole locations using the base as a template.

3. Drill two suitable sized holes.

4. With mirror in place, use two #10 screws and fasten to dash.

5. After mirror is mounted, adjust to desired position. If mirror cannot

be adjusted sufficiently, rotate the mirror head one-half turn.

(The mirror may need to be removed from the dash to do so.)

NOTE: Mirror head tension does not require adjustment; a

permanent tension system is built in and preset by Attwood.

WINDSHIELD-MOUNTED SKI MIRROR

NOTE: Windshield installation is not recommended for frameless

windshields.

Tools and Materials Required for Installation

1. Phillips Head screwdriver.

2. Optional metal cutting file.

3. Optional aluminum, plastic, plywood spacer.

INSTALLATION INSTRUCTIONS

1. Select a desirable location at or near centerline of the windshield.

chrome finish.

2. Loosen the two screws in the clamping bracket, then place it over

the windshield frame and mirror base at the selected location.

(Figure 2)

OPTION 1

For windshield frames less than .450" thick, or a

stepped frame (Figure 3), a small spacer of aluminum,

plastic, or marine plywood may be used between the

base and the windshield frame.

OPTION 2

For windshields with a stepped frame (Figure 3),

using the mounting bracket as a template, mark the

width of the bracket on the windshield frame step.

03-10

Using a file, remove the step from this area.

Figure 2

Figure 3

3. Tighten two clamping bracket screws.

CAUTION: Overtightening the screws could cause damage to the

threads, clamping bracket, windshield/windshield frame.

4. After mirror is mounted, adjust to desired position. If mirror cannot

be adjusted sufficiently, rotate the mirror head one-half turn. (The

mirror may need to be removed to do so.)

NOTE: Mirror head tension does not require adjustment; a

permanent tension system is built in and preset by Attwood.

ATTWOOD LIMITED WARRANTY

Attwood Corporation, 1016 North Monroe, Lowell, Michigan 49331 ("Attwood") warrants

to the original consumer purchaser that Attwood brand products will be free from defects

in materials and workmanship under normal use and service for one year from the date

of original consumer purchases.

This limited warranty is not applicable if the product has been damaged by accident,

improper installation, unreasonable or improper use, lack of proper maintenance,

unauthorized repairs or modifications, normal wear and tear, or other causes not

arising out of defects in materials or workmanship.

Attwood products are warranted for use on pleasure boats. Any other use – including

but not limited to commercial, racing, or non-marine use – are not covered under this

warranty. Attwood's obligation under this warranty is limited to repair of the product at

Attwood's plant or replacement of the products at Attwood's option without expense to

the original consumer purchaser. Any expenses involved in the removal, reinstallation

or transportation of the product are not covered by this warranty. The product must be

returned to Attwood's plant at the address above, postage pre-paid, and insured with

proof of original purchase including date. If Attwood is unable to replace the product and

repair is not commercially practical or cannot be timely made, or if the original consumer

purchaser is willing to accept a refund in lieu of repair or replacement, Attwood may

refund the purchase price, less an amount for depreciation. The acceptance by Attwood

of any product returned or any refund provided by Attwood shall not be deemed an

admission that the product is defective or in violation of any warranty. Products that

are replaced or for which a refund is issued become the property of Attwood.

THIS WARRANTY IS ATTWOOD'S ONLY EXPRESSED WARRANTY OF THESE

PRODUCTS. NO IMPLIED WARRANTY INCLUDING, WITHOUT LIMITATION, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, SHALL BE EXTENDED BEYOND THE WARRANTY PERIOD STATED

ABOVE FOR EACH PRODUCT. ATTWOOD SHALL NOT BE LIABLE FOR ANY

DAMAGES, FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER

INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS, OR EXPENSES.

Some states do not allow limitations or how long an implied warranty lasts or the exclusion

or limitation of incidental or consequential damages, so the above limitations and exclusions

may not apply to you. This warranty gives you specific legal rights, and you may have

other rights which vary from state to state.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Windshield Frame

Tighten

Screw

Adjust

Step