Aube Technologies TH132 F Owner's Manual - Page 3

Browse online or download pdf Owner's Manual for Control Unit Aube Technologies TH132 F. Aube Technologies TH132 F 3 pages. Programmable control module
Also for Aube Technologies TH132 F: Owner's Manual (2 pages), Owner's Manual (3 pages), Owner's Manual (2 pages)

Print Page

Aube Technologies TH132 F Owner's Manual

The PB130-230 power base is used to power a TH13x Series control

module. The resistive load must not exceed 3450 watts (NI) @

230 VAC (15 A).

Parts

One (1) PB130-230 power base

One (1) floor sensor (for AF and F control modules only)

One (1) wall plate (optional, in certain countries)

Guidelines

Turn off power to the heating system at the main power panel to avoid

electrical shock. Installation should be carried out by an electrician.

All work must conform to the applicable country standards for

electrical installations and wiring.

This thermostat should be connected on a circuit equipped with

a fuse or a circuit breaker. It must be installed on a certified

electrical box.

For a new installation, choose a location about 1.5 m above the

floor.

For electric baseboards, convectors and fan-forced heaters, the

thermostat must be installed facing the heating system.

The thermostat must be installed on an inside wall.

Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or

concealed chimneys or stove pipes.

Technical Specifications

Model: PB130A-230

Supply: 230 VAC, 50 Hz

Load: 15 A maximum (resistive only)

Power: 3450 Watts (NI) @ 230 VAC

Conformity: EN60730-2-9 / EN50081-1 / EN50082-2

Storage: -20°C to 50°C

Protection: Class 2

Protection

degree: IP21

Automatic

action: Type 1.B

Environment: Normally polluted

Size (H • W • D)

: 2.95 x 2.95 x 0.55 in. (75 x 75 x 14 mm)

NOTE:

The terminals are designed to handle a cross-section of wire

measuring 0.33 to 3.1 mm

Procedure

Remove the screw holding the

control module to the power base

and lift the lower part upwards.

The screw cannot be completely

removed.

PB130

Before making the connections, make sure

that the base covers the electrical box

entirely. If not, install a wall plate at the

back of the base as shown.

Connect the wires:

• Power:

Terminals 1 & 5

• Load:

Terminals 2 & 4

see note 1

•

Pilot

Wire:

Terminal 3

see note 2

•

Floor

sensor:

Terminals 6 & 7

(no polarity)

see note 3

Note 1

If a contactor is used between the thermostat and the load,

install a snubber at the contactor's coil terminal to ensure

the proper operation of the thermostat.

Note 2

This connection is required on some models only.

Note 3

For the proper operation of the thermostat, the floor sensor

must be centered between two heater wires having a

maximum temperature of 80°C. The floor sensor wire must

not cross any heater wire or be placed close to it.

Push wires into the electrical box and

secure the base to the electrical box

anchorage. The head of the screw

must be less than 2 mm thick.

BEFORE installing the control

module onto the base, set the

configuration switches (if any)

on the control module

the user

guide).

WARNING: This power base must be used

heating cycles. If your control module has a selector switch for

choosing the heating cycle, ensure that the switch is correctly set.

Return power to the heating system.

PB130

Installation Instructions

230 V Line Voltage Power Base

(refer to

only

with

400-130-001-E

19/9/05

15-minute

1/1