CON-TEC DLUX 80 N++ Manual - Page 2
Browse online or download pdf Manual for Bicycle Accessories CON-TEC DLUX 80 N++. CON-TEC DLUX 80 N++ 2 pages. Bike led front light
Print Page
Front light adjustment
10m
Align the LED front light so that the light beam reaches the road approx. 10 meters in front of
the wheel (see ill.).
Attention!
Check regularly the correct setting of your front light. The light beam of the LED front light
must point straight in direction from 400 up to 1200mm.
Front reflector assembly (optional)
It is possible to mount a white reflector (2) to the bottom of the front light (1). The reflector is
equipped with two pins that adapt into the holes of the front light. Screw the reflector to the
front light for a permanent attachment.
Operation
The front light has an automatic mode. The sensor (S) located at the rear is permanently
active. As soon as the sensor (S) detects that there is not enough daylight, the front light will
turn on.
Standlight function
When the front light is switched on, the standlight function is automatically activated. The power is
supplied by a maintenance-free capacitor which is fully charged after approx. 4 minutes of
operation. As soon as the bike stops, the LED lights for another 4 minutes.
Manual_DLUX 80
Dispose of packaging and devices in an environmentally friendly way!
The packaging is made of environmentally friendly materials which you
can dispose of at local recycling centers. Throw your device if it has
been used in the interests of environmental protection, not in the
household waste, but run it to a proper disposal. You can find out about
collective places and their opening times by your responsible
management. Disposal of the disused device is available at your local or
city government office.
Cleaning
Clean the device only with a slightly damp, lint-free cloth. Never completely immerse the device
under water. Do not use any corrosive or abrasive cleaners. This causes damage to the device.
Warranty conditions
Dear Customer, you will receive a 2-year warranty on this device from the date of purchase. In the
event of defects in this product, you have legal rights against the seller of the product. These legal
rights are not limited by the warranty below.
Guarantee conditions
The warranty period begins with the date of purchase. Please keep the original receipt. This
document is required as a proof of purchase. If a defect in material or workmanship occurs within
2 years from the date of purchase of this product, the product will be repaired or replaced by us at
our discretion free of charge. This warranty requires that within the 2-year period, the defective
device and the proof of purchase (receipt) presented and briefly described in writing, what the
defect is and when it occurred. If the defect is covered by our warranty, you will receive the
repaired or a new product back. Repair or replacement of the product does not commence a new
warranty period. The guarantee time is not extended by the guarantee. This also applies to
replaced and repaired parts. Any damage and defects already existing at the time of purchase must
be reported immediately after unpacking. After the warranty period incurred repairs are chargeable.
Warranty scope
The device has been carefully produced according to strict quality guidelines and METI-culously
checked before delivery. The warranty applies to material or manufacturing defects. This warranty
does not cover product parts that are subject to normal wear and tear and can be considered as
wearing parts or for damage to fragile components, such as switches, batteries or part made of
glass. This warranty is void if the product has been damaged, improperly used or serviced. For
proper use of the product, all instructions given in the operating instructions must be exactly
followed. Uses and actions that are advised against or warned against in the operating
instructions are to be absolutely avoided. The product is intended for private and non-commercial
use only. Abusive and improper handling, use of force and internal tampering not carried out by
our authorized service branch, the warranty will be void. If malfunctions or other defects occur,
please first contact the service department named below by phone or e-mail.
Product features
DLUX 80 N++
Model:
Luminosity:
80 LUX
Nominal voltage:
6 V
Nominal power:
4 W
SERVICE + SUPPLIER
Hermann Hartje KG
Deichstr. 120-122
27318 Hoya
Tel.: 04251/811-0
www.contec-parts.com