DAM MADCAT TOPCAT Manual - Page 4

Browse online or download pdf Manual for Security System DAM MADCAT TOPCAT. DAM MADCAT TOPCAT 13 pages.

Print Page

SPECIFICATIONS

Battery type:

Nominal voltage:

Battery capacity:

Power off current:

Peak working current:

Wireless transmition modulation code:

Radio transmitter operating frequency:

Effective operating distance of wireless transmission:

USER MANUAL RECEIVER (RX)

How to switch the alarm on?

Long press the power button (for two seconds) to switch on the alarm. The color LED lights will flash three times and the speaker will sound three times, to indicate that the

alarm has been activated in the standby mode.

How to adjust the volume?

In the standby mode press the "+" button briefly to up the volume and press the "-" button briefly to turn down the volume. There are seven levels of volume to choose from:

zero to six, zero being mute, seven being the loudest (102dB).

Can I adjust the tone?

Tones are not adjustable. Each color of alarm has its own, different tone, but all alarms have the same low town for a drop back bite and the same high tone for a slow bite.

How to switch on the night light?

In the standby mode, long press the "+" button to enable or disable the night light (slightly lid blue).

How to quick mute the sound?

In the standby mode long press the "-" button to mute the sound. A prompt will indicate when the mute function is activated. Press any button to exit the mute mode.

How to adjust the sensitivity?

Short press the power button to switch from volume mode to sensitivity mode. A blue LED will light up, to indicate that the alarm is in sensitivity mode. Press the "+" button

briefly to up the snesitivity and press the "-" button briefly to lower the sensitivity. There are four levels of volume to choose from. When you switch sensitivity level, a prompt

will sound: one prompt for the lowest level, two for the next, three for the next and four prompts for the highest level of sensitivity. If you don't adjust the sensitivity for 5

seconds, the alarm will automatically switch back to the standby mode (volume mode).

How to charge the alarm?

The alarm has a built build-in, rechargeable li-on battery that can be charged at anytime. A red LED will flash while unit is on charging. When charging is completed, a green

LED will light up. How long the charging takes, depends on how powerful the source is, but it takes at least 2,5 hours. After that the alarms will work about 240 hours in

standby mode. Fully charged the internal li-on battery will last about the same time as two normal AAA batteries.

How to switch the alarm off?

Long press the power button (for two seconds) to switch off the alarm. A white LED will flash once and the speaker will sound once, to indicated that the alarm has been

switched off.

FUNCTIONS

Memory function

When you switch the alarm off, it will automatically remember the settings, for when you want to turn it back on.

Low battery-alert

When the internal battery is running low, a red LED will be lit and the speaker will tick, to indicate that the alarm has to be recharged as soon as possible. Once the low

battery-alert has kicked in, it takes a while before the alarm stops working totally if only on standby. If used intensively the remaining time will be considerably less! When the

low battery-alarm goes off, the battery has less than 20% power left.

Anti theft-alarm

When the alarm is being switched off, the receiver will blink and bleep for 30 seconds. Press any button on the receiver to kill the anti theft-alarm.

Vibration-alarm

After the alarm has been attached to the rod and switched on, it calculates the angle it is in. When this angle changes because of vibration, the alarm lights will flash and

bleeps will sound, on both the alarm and the receiver. A sudden forward movement triggers the color LED and the corresponding tone. A sudden backward vibration triggers

the white LED and a low tone. When the vibrating stops, the color or white LED will stay lit for 20 secconds.

Slow bite-alarm

When the rods slowly bends down deep, it will trigger the color LED and a high tone for 10 seconds (on both the alarm and receiver). After that 10 seconds the alarm will

automatically be repeated, until the alarm has returned to its original angle.

Drop back-alarm

When a break line snaps, often the main line slackens for a moment, resulting in the rod bouncing back. This will trigger the white LED and a low tone for 10 seconds (on both

the alarm and receiver). After that 10 seconds the alarm will automatically be repeated, until the alarm has been switched off.

NOTICE

Do not over charge the battery. When the green LED lights up, remove the alarm from the charging device.

Each transmitter has its own, unique identity code: only the paired receiver can decode that signal.

Clean after usage and store in a dry place.

902030P li-on

3.7V

500mAH

0.02mA

150mA

433.92MHz

100M