ADDER X-DVIPRO-DL User Manual - Page 16

Browse online or download pdf User Manual for Extender ADDER X-DVIPRO-DL. ADDER X-DVIPRO-DL 17 pages.

Print Page

SAFETY INFORMATION

• For use in dry, oil free indoor environments only.

• Do not use to link between buildings.

• Ensure that the twisted pair interconnect cable is installed in compliance with all

applicable wiring regulations.

• Do not connect the CATx link interface (RJ45 style connector) to any other

equipment, particularly network or telecommunications equipment.

• Warning – the power adapter contains live parts.

• No user serviceable parts are contained within the power adapter - do not dismantle.

• Plug the power adapter into an earthed socket outlet close to the unit that it is

powering.

• Replace the power adapter with a manufacturer approved type only.

• Do not use the power adapter if the power adapter case becomes damaged, cracked

or broken or if you suspect that it is not operating properly.

• If you use a power extension cord with the units, make sure the total ampere rating of

the devices plugged into the extension cord do not exceed the cord's ampere rating.

Also, make sure that the total ampere rating of all the devices plugged into the wall

outlet does not exceed the wall outlet's ampere rating.

• The units and power supplies can get warm in operation – do not situate them in an

enclosed space without any ventilation.

• The units do not provide ground isolation and should not be used for any applications

that require ground isolation or galvanic isolation.

WARRANTY

Adder Technology Ltd warrants that this product shall be free from defects in

workmanship and materials for a period of two years from the date of original purchase.

If the product should fail to operate correctly in normal use during the warranty period,

Adder will replace or repair it free of charge. No liability can be accepted for damage due

to misuse or circumstances outside Adder's control. Also Adder will not be responsible

for any loss, damage or injury arising directly or indirectly from the use of this product.

Adder's total liability under the terms of this warranty shall in all circumstances be

limited to the replacement value of this product.

If any difficulty is experienced in the installation or use of this product that you are

unable to resolve, please contact your supplier.

RADIO FREQUENCY ENERGY

A Category 6a (or better) twisted pair cable must be used to connect the units in order

to maintain compliance with radio frequency energy emission regulations and ensure a

suitably high level of immunity to electromagnetic disturbances.

All other interface cables used with this equipment must be shielded in order to maintain

compliance with radio frequency energy emission regulations and ensure a suitably high

level of immunity to electromagnetic disturbances.

European EMC directive 2004/108/EC

This equipment has been tested and found to comply with the limits for a class A

computing device in accordance with the specifications in the European standard

EN55022. These limits are designed to provide reasonable protection against harmful

interference. This equipment generates, uses and can radiate radio frequency energy

and if not installed and used in accordance with the instructions may cause harmful

interference to radio or television reception. However, there is no guarantee that

harmful interference will not occur in a particular installation. If this equipment does

cause interference to radio or television reception, which can be determined by turning

the equipment on and off, the user is encouraged to correct the interference with one

or more of the following measures: (a) Reorient or relocate the receiving antenna.

(b) Increase the separation between the equipment and the receiver. (c) Connect

the equipment to an outlet on a circuit different from that to which the receiver is

connected. (d) Consult the supplier or an experienced radio/TV technician for help.

FCC Compliance Statement (United States)

This equipment generates, uses and can radiate radio frequency energy and if not

installed and used properly, that is, in strict accordance with the manufacturer's

instructions, may cause interference to radio communication. It has been tested and

found to comply with the limits for a class A computing device in accordance with

the specifications in Subpart J of part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when the equipment is operated in a

commercial environment. Operation of this equipment in a residential area may cause

interference, in which case the user at his own expense will be required to take whatever

measures may be necessary to correct the interference. Changes or modifications not

expressly approved by the manufacturer could void the user's authority to operate the

equipment.

Canadian Department of Communications RFI statement

This equipment does not exceed the class A limits for radio noise emissions from digital

apparatus set out in the radio interference regulations of the Canadian Department of

Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le règlement sur le

brouillage radioélectriques publié par le ministère des Communications du Canada.