3onedata IES6312-8GP4GF-2P24-120W Quick Installation Manual - Page 2
Browse online or download pdf Quick Installation Manual for Network Router 3onedata IES6312-8GP4GF-2P24-120W. 3onedata IES6312-8GP4GF-2P24-120W 4 pages. Managed industrial poe/non-poe ethernet switch
Print Page
3.
DIP switch
4.
Console port
5.
Grounding screw
6.
Wall mounting screw hole
7.
DIN-Rail mounting kit
8.
Power supply indicator P1/P2/PWR
9.
Relay alarm indicator ALM
10.
Device running indicator RUN
11.
PoE indicator PoE+
12.
Interface connection indicator Link
13.
Gigabit PoE port
14.
Gigabit fiber port
15.
Gigabit copper port
16.
Gigabit SFP slot
【Mounting Dimension】
Unit: mm
Notice:
The hanging panel accessories on the right side of the
picture above need additional purchase.
Attention before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:
Step 1
Check if the DIN-Rail mounting kit is installed firmly.
Step 2
Insert the bottom of DIN-Rail mounting kit (one side
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Step 3
Check and confirm the product is firmly installed on
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Step 1
Device power off.
Step 2
After lift the device upward slightly, first shift out the
top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
Attention before power on:
Power ON operation: first connect power line to the
connection terminal of device power supply, then
power on.
Power OFF operation: first unpin the power plug,
then remove the power line, please note the
operation order above.
【Power Supply Connection】
DC power supply
The series provide 6-pin 5.08mm pitch
terminal blocks, and two independent
DC power supply systems of PWR1
and PWR2. PIN1-PIN4 are used for
power supply input. This series provide
8 types of product and adopt 4 different
power supply ranges. Please be aware of the corresponding
power supply type of the device lest damaging the device.
24VDC PoE device
The power supply of 24VDC PoE device model I and model II
has built-in 12A over-current protection, and support
anti-reverse connection and redundant backup. Input power is
24VDC.
48VDC PoE device
The power supply of 48VDC PoE device model III, model IV,
model V and model VI has built-in 5A over-current protection,
and support anti-reverse connection and redundant backup.
Input power is 48VDC.
12~48VDC non-PoE device
The power supply of 12~48VDC non-PoE device model VII
and model VIII has built-in 3A over-current protection, and
support non-polarity and redundant backup. Input power
range is 12~48VDC.
AC power supply
This series provide 6 pins 5.08mm
pitch terminal blocks and AC power
supply system.
220VAC non-PoE device
The power supply of 220VAC
non-PoE device model IX and model X has built-in 5A
over-current protection. Input power range is 100~240VAC.
【Relay Connection】
This series of products provide 6-pin
5.08mm pitch terminal blocks. Relay
terminals are a pair of normally open
contacts in device alarm relay. They
are open circuit in normal non alarm
state,
closed
when
any
alarm