Concoa 806 7014 Quick Start Manual

Browse online or download pdf Quick Start Manual for Controller Concoa 806 7014. Concoa 806 7014 2 pages.

Print Page
CERTIFIED ISO 9000
SPECIAL PURPOSE REGULATORS
Protect yourself and others. Before installing, operating or
servicing, read and comply with these instructions.
USER RESPONSIBILITY
This equipment will perform in conformity with the description
thereof contained in this manual and accompanying labels and/
or inserts when installed, operated, and maintained in accor-
dance with the instructions provided. This equipment must be
checked periodically. Defective equipment should not be used.
Parts that are missing, plainly worn, distorted or contaminated,
should be replaced immediately. Should such repair or re-
placement become necessary, CONCOA recommends that a
telephone or written request for service advice be made to
CONCOA Customer Service in Virginia Beach, Virginia,
PHONE: 1-800-225-0473, FAX: 1-757-422-3125, or E-MAIL:
This equipment or any of its parts should not be altered without
prior written approval of CONCOA. The user of this equipment
shall have the sole responsibility for any malfunction which
results from improper use, faulty maintenance, damage, im-
proper repair or alteration by anyone other than CONCOA or a
designated CONCOA service facility.
WARNING
FUMES and GASES can be dangerous to your health.
HEAT RAYS (INFARED RADIATION from flame or hot metal)
can injure eyes.
Read and understand the manufactures's instruction and
your employer's safety practices.
Keep you head our of the fumes.
Use enough ventilation, exhaust at the flame, or both, to
keep fumes and gases from your breathing zone and the
general work area.
Wear correct eye, ear and body protection.
See American National Standard Z49.1 "Safety in Welding
and Cutting," published by the American Welding Society,
Box 351040, Miami, FL; CFR 1910 available from U.S.
Government Printing Office, Washington, D.C. 20402
CAUTION
Make all connections tight. ATTACH MAPP REGULATOR
a. Check that connecting surfaces of MAPP regulator and
cylinder valve are free of foreign matter and undamaged.
Remove any foreign matter that may be present by wiping
surfaces clean with a clean lint-free cloth.
b. Back out knurled-knob pressure-adjusting screw counter-
clockwise all the way.
c. Fit bottom of regulator over cylinder outlet threads and screw
on clockwise by hand until it bottoms and stops.
d. With regulator knob backed out loose, NO gas should flow
from regulator. If it does, immediately unscrew regulator
from cylinder and return it for repair.
It is recommended that defective parts be replaced with a part
manufactured or sold by the manufacturer. Inspection, trouble
shooting, repairs, and all other servicing should be done by an
authorized service facility. Contact the distributor from whom
purchased for assistance.
If so advised, the unit should be sent to a service facility autho-
rized by the manufacturer, securely packaged, in the original
shipping container (if possible), and shipped prepaid, with a
statement of deficiency. In all cases other than where warranty
is applicable, repairs will be made at current list price for the
replacement part(s) plus a reasonable labor charge.
TESTING
To prevent use under unsafe operating conditions, check the
regulator for leaks after each reconnection, and regularly test
ADI 3086-C
806 7014
806 7019
July 2000
Supersedes January 2000
CERTIFIED ISO 9000
SPECIAL PURPOSE REGULATORS
Protect yourself and others. Before installing, operating or
servicing, read and comply with these instructions.
USER RESPONSIBILITY
This equipment will perform in conformity with the description
thereof contained in this manual and accompanying labels and/
or inserts when installed, operated, and maintained in accor-
dance with the instructions provided. This equipment must be
checked periodically. Defective equipment should not be used.
Parts that are missing, plainly worn, distorted or contaminated,
should be replaced immediately. Should such repair or re-
placement become necessary, CONCOA recommends that a
telephone or written request for service advice be made to
CONCOA Customer Service in Virginia Beach, Virginia,
PHONE: 1-800-225-0473, FAX: 1-757-422-3125, or E-MAIL:
This equipment or any of its parts should not be altered without
prior written approval of CONCOA. The user of this equipment
shall have the sole responsibility for any malfunction which
results from improper use, faulty maintenance, damage, im-
proper repair or alteration by anyone other than CONCOA or a
designated CONCOA service facility.
WARNING
FUMES and GASES can be dangerous to your health.
HEAT RAYS (INFARED RADIATION from flame or hot metal)
can injure eyes.
Read and understand the manufactures's instruction and
your employer's safety practices.
Keep you head our of the fumes.
Use enough ventilation, exhaust at the flame, or both, to
keep fumes and gases from your breathing zone and the
general work area.
Wear correct eye, ear and body protection.
See American National Standard Z49.1 "Safety in Welding
and Cutting," published by the American Welding Society,
Box 351040, Miami, FL; CFR 1910 available from U.S.
Government Printing Office, Washington, D.C. 20402
CAUTION
Make all connections tight. ATTACH MAPP REGULATOR
a. Check that connecting surfaces of MAPP regulator and
cylinder valve are free of foreign matter and undamaged.
Remove any foreign matter that may be present by wiping
surfaces clean with a clean lint-free cloth.
b. Back out knurled-knob pressure-adjusting screw counter-
clockwise all the way.
c. Fit bottom of regulator over cylinder outlet threads and screw
on clockwise by hand until it bottoms and stops.
d. With regulator knob backed out loose, NO gas should flow
from regulator. If it does, immediately unscrew regulator
from cylinder and return it for repair.
It is recommended that defective parts be replaced with a part
manufactured or sold by the manufacturer. Inspection, trouble
shooting, repairs, and all other servicing should be done by an
authorized service facility. Contact the distributor from whom
purchased for assistance.
If so advised, the unit should be sent to a service facility autho-
rized by the manufacturer, securely packaged, in the original
shipping container (if possible), and shipped prepaid, with a
statement of deficiency. In all cases other than where warranty
is applicable, repairs will be made at current list price for the
replacement part(s) plus a reasonable labor charge.
TESTING
To prevent use under unsafe operating conditions, check the
regulator for leaks after each reconnection, and regularly test
ADI 3086-C
806 7014
806 7019
July 2000
Supersedes January 2000