Addis TK-12-5L Owner's Manual - Page 5

Browse online or download pdf Owner's Manual for Kitchen Appliances Addis TK-12-5L. Addis TK-12-5L 9 pages.

Print Page

hOw TO OpERATE ThE ADDIS ThERmO pOT...

cONTINUED

AUTO cUT-OFF

In the event that the Thermo pot runs dry, the 'auto cut-off'

function will be activated. The power source will be cut-off and at the

same time, the beeper will sound and a sign will be displayed on the

LCD panel.

Causes of auto cut-off:

• The power is on, but the Thermo pot is not filled

• Water level is below 'add water' indicator but water is still boiling

• If no water is added when the water is used up

• The lid is not secured properly

Solution:

• Switch off the power supply, allow the unit to cool, add

water, and then turn on appliance again

Care should be taken to ensure that the Thermo pot does

not run dry as this can damage the appliance, and this is

not covered by our guarantee.

The Thermo pot is designed to remain switched

on at all times during normal domestic use. If the Thermo

pot is not used for 72 hours it will automatically turn itself off and the following

flashing symbol will appear in the green LCD display.

To use the appliance again touch any key. It is however essential that if the water

has been standing for this length of time, it is discarded completely and the Thermo

pot filled with fresh water, and flushed through before normal

use is resumed.

If the Thermo pot is not being used for an extended period of time (in excess of 72

hours) then it is recommended that the appliance is disconnected from the mains,

emptied and left open to air in the upright position. Ensure that water is cleared from

all outlets by gently inverting the appliance until there is no water flowing from the

spout. When it is used again it should be filled and boiled once flushing the water

through to rinse the pipes. Empty the residual water at the bottom of the Thermo pot

when the auto-dispensing is finished, rinse the internal pot to remove any loose lime

scale, and commence normal use.

RE-BOIL FUNcTION

• Additional water can be added to the ADDIS Thermo pot to top it up at anytime

(though not when the boil function is active) and this will trigger the automatic boil

function to operate. If however the added water is not sufficient

to start the automatic boiling function then it may be necessary to press the

re-boil button.

REFILL LED

1. Press 're-boil' button once. The re-boiling indicator light will light up.

will be lit

2. After 're-boil' is completed, the 'keep warm' indicator light will be lit.

• Re-boil will not function if there is insufficient water in the appliance

• Pressing the re-boil' button immediately after the water has just reached boiling

point will have no effect as the water is already at 100°c

• The temperature needs to cool to 94ºc before the 're-boil' button can be pushed to

achieve a rolling boil again. If a rolling boil is needed again when the temperature is

between 95ºc - 98ºc this can be achieved by moving the temperature selector down

through the temperature settings and re-selecting 98ºc

DISpENSINg wATER

1. Auto dispense water outlet

a) Press the 'unlock' key once. The 'unlock' indicator light will come on.

b) Push the 'auto dispense' button to dispense hot water.

2. cup water outlet

a) Press the 'unlock' key once. The 'unlock' indicator light will come on.

b) Use cup touch dispenser water outlet by placing cup under the outlet and raise the

cup slightly upwards.

• If the dispense button or cup switch dispense button is not selected within 10

seconds after selecting the UNLOCK key, the appliance will automatically revert

back to the LOCK position

• Do not press the dispensing button when the inner water reservoir is empty. (Doing

so can cause damage)

• The "Auto" and "Cup Water Outlet" dispensing functions will NOT operate if the

electric Thermo pot is not connected to the mains supply. (Use Air Pump dispensing

as No. 3 below)

3. manual air pump water outlet (can be used without power connection)

Put the cup under the water outlet. Depress the centre section of the lid manually

ensuring that the "unlock" position has been selected. Ensure that the manual air pump

is locked again after use.

ownERs GUIDE | THERmo PoT