airwave Fairwind series Installation Manual

Browse online or download pdf Installation Manual for Air Conditioner airwave Fairwind series. airwave Fairwind series 2 pages. (split wall-mounted type)

Print Page

202000192582

CS236I-BP12FU(L) 20131022

INSTALLATION MANUAL FOR

ROOM AIR CONDITIONER

(Split Wall-Mounted Type)

INSTALLATION PRECAUTIONS

Please read this installation manual carefully before operating the unit to ensure correct installation.

If the power cord is damaged, replacement work shall be performed by authorised personnel only.

Installation work must be performed in accordance with the national wiring standards by authorised

personnel only.

Contact an authorized service technician for repair, maintenance and installation of this unit.

This appliance is not intended for use by persons(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by persons responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

All the pictures in the instructions are for explanation purposes only. The actual shape should prevail.

The design and specifications are subject to change without prior notice for product improvement.

Consult with the sales agency or manufacturer for details.

SAFETY PRECAUTIONS

Please read these safety precautions carefully before installation

Be sure to follow all the precautions below, they are all important for ensuring safety.

This symbol indicates the possibility of death or serious injury.

WARNING

This symbol indicates the possibility of injury or damage to property.

CAUTION

WARNING

1) Install according to this installation instructions strictly. If installation is defective, it will cause water

leakage, electrical shock,or fire.

2) Use the included accessories parts and specified parts for installation. otherwise, it will cause the set

to fall, water leakage, electrical shock,or fire.

3) Install at a strong and firm location which is able to withstand the set s weight. If the strength is not

enough or installation is not properly done, the set will drop and cause injury.

4) For electrical work, follow the local national wiring standard, regulation and this installation instructions.

An independent circuit and single outlet must be used. If electrical circuit capacity is not enough or

defect found in electrical work, it will cause electrical shock,or fire.

5) Use the specified cable and connect tightly and clamp the cable so that no external force will be acted

on the terminal. If connection or fixing is not perfect, it will cause heat-up or fire at the connection.

6) Wiring routing must be properly arranged so that control board cover is fixed properly. If control board

cover is not fixed perfectly, it will overheat at connection point of terminal, fire or electrical shock.

7) When carrying out piping connection, take care not to let air substances other than the specified

refrigerant go into refrigeration cycle. Otherwise, it will cause lower capacity, abnormal high pressure

in the refrigeration cycle, explosion and injury.

8) Do not modify the length of the power supply cord or use of extension cord, and do not share the

single outlet with other electrical appliances. Otherwise, it will cause fire or electrical shock.

CAUTION

1) This equipment must be grounded and installed with ground leakage current breaker. It may cause

electrical shock if grounding is not perfect.

2) Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and

accumulates at surrounding of the unit, it may cause fire.

3) Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water

may enter the room and damage the furniture.

SELECT THE BEST LOCATION

Indoor unit

There should not be any heat source or stream

near the unit.

There should not be any obstacles blocking the

air circulation.

A place where air circulation in the room is good.

A place where drainage can be easily done.

A place where noise prevention is taken into

consideration.

Do not install the unit near the door way.

Ensure the spaces indicated by arrows from the

wall,ceiling,fence or other obstacles.

There should not be any direct sunlight. If unavoidable,

sunlight prevention should be taken into consideration.

Outdoor unit

If an awning is built over the unit to prevent

direct sunsight or rain,be careful that heat

radiation from the condenser is not obstructed.

There should not be any animal or plant which

could be affected by hot air discharged.

Keep the spaces indicated by arrow from wall

ceiling, fence or other obstacles.

Do not place any obstacles which may cause

a short circuit of the discharged air.

Settlement of outdoor unit

Anchor the outdoor unit with a bolt and nut φ10 or

φ8 tightly and horizontally on a concrete or rigid mount.

NOTE: The outdoor unit you purchase may be like one

of the following. Install the outdoor unit according to the

dimension as indicated in the table below:

Mounting dimensions

Outdoor unit dimension

mm(WxHxD)

A(mm)

B(mm)

700x540x240

458

250

685x430x260

460

276

780x540x250

549

276

760x590x285

530

290

845x700x320

560

335

810x558x310

549

325

670x540x265

481

276

ACCESSORIES

Number

Name of Accessories

Installation Plate

Clip Anchor

Self-tapping Screw A ST3.9x25

Seal(For cooling & heating models only)

Drain Joint(For cooling & heating models only）

Φ6.35

Liquid side

Connecting

Φ9.52

pipe

Φ9.52

Assembly

Φ12.7

Gas side

Φ 16

Remote controller

Self-tapping Screw B ST2.9x10

Remote controller holder

Air freshening filter(used to install on Air filter)

Except the above parts provided,the other parts needed during installation you must

NOTE:

purchase.

Air inlet

Air outlet

Qty

5-8(depending on models)

Parts you must purchase. The pipe

size differ from appliance to appliance.

Consult the technician for the proper

size.

optional

parts

INSTALLATION PLATE MOUNTING

NOTE:

The mounting wall is strong and solid

enough to prevent it from the vibration.

Installation Plate Mounting

1. Fit the installation plate horizontally

on structural parts of the wall with

spaces around the installation plate.

2. If the wall is made of brick, concrete

or the like, drill five or eight 5mm

diameter holes in the wall.Insert Clip

anchor for appropriate mounting screws.

3. Fit the installation plate on the wall

with five or eight type

screws.

NOTE:

Mount the Installation Plate and drill

holes in the wall according to the

wall structure and corresponding

mounting points on the installation

plate. The installation plate provided

with the machine differ from appliance

to appliance.

(Dimensions are in mm unless

otherwise stated)

Correct orientation

of Installation Plate

DRILL A HOLE IN THE WALL

1. Determine hole positions according to left and right

side of the installation plate. The hole center is obtained

by measuring the distance as shown in the diagram above.

2. Dirll the piping plate hole with φ65mm hole-core drill.

3. Drill the piping hole at either the right or the left and the

hole should be slightly slanted to the outdoor side.

4. Always take steps to protect the pipe when drilling metal

grid,metal plate or the like.

CONNECT THE CABLE TO THE INDOOR UNIT

Electrical work

Electric safety regulations for the initial Installation

1. If there is serious safety problem about the power supply, the technicians should refuse to install

the air conditioner and explain to the client until the problem is solved.

2. Power voltage should be in the range of 90%~110%of rated voltage.

3. The surge protector and main power switch with a 1.5 times capacity of Max. Current of the unit should

be installed in power circuit. Ensure the air conditioner is grounded well.

4. The appliance shall be installed in accordance with national wiring regulations. Do not operate your air

conditioner in a wet room such as a bathroom or laundry room.

5. An all-pole disconnection device which has at least 3mm clearances in all poles, and have a leakage

current that may exceed 10mA, the residual current device(RCD) having a rated residual operating

current not exceeding 30mA, and disconnection must be incorporated in the fixed wiring in accordance

with the wiring rules.

6. For the unit adopts auxiliary electric heater, keep at least 1 meter away from the nearest combustible

materials.

7. According to the attached Electrical Connection Diagram located on the panel of the indoor & outdoor

unit to connect the wire.

8. All wiring must comply with local and national electrical codes and be installed by qualified and

skilled electricians.

9. An individual branch circuit and single receptacle used only for this air conditioner must be

available. See the following table for suggested wire sizes and fuse specifications:

Minimum cross-sectional area of conductors:

Rated current

Nominal cross-sectional

of appliance

area

(A)

(mm2)

>3 and ≤6

>6 and ≤10

>10 and ≤16

>16 and ≤25

>25 and ≤32

>32 and ≤40

Connect the cable to the indoor unit

NOTE:

Before performing any electrical work, turn off the main power to the system.

1. The inside and outside connecting cable can be connected without removing the front grille.

2. The indoor power cord type is H05VV-F or H05V2V2-F, the outdoor power cord and

interconnected cord type is H07RN-F.

3. Lift the indoor unit panel up, remove the electrical box cover by loosening the screw.

4. Ensure the colour of wires of outdoor unit and the terminal Nos. are the same to the indoor s

respectively.

5. Wrap those cables not connected with terminals with insulation tapes, so that they will not touch

any electrical components. Secure the cable onto the control board with the cord clamp.

NOTE: If used as MONO unit, for the standby control needs, the cross section area of cable connected

to L(1)/W, 1/1(L), 2(N) must be sufficient for the maximum system current. The maximum system current is

equal to the sum of indoor unit and outdoor unit rated current. If used as MULTI unit, L(1)/W on the

terminal block does not need to be connected.

Front Panel

Electronic box

cover

CONNECTIVE PIPE AND DRAINAGE INSTALLATION

Drainage

1. Run the drain hose sloping downward.

Do not install the drain hose as illustrated

in wrong figures.

2. When connecting extension drain hose,

insulate the connecting part of extension

drain hose with a shield pipe, do not let

the drain hose slack.

150mm or more to ceiling

120mm or

more to wall

Left rear side

refrigerant

pipe hole φ65

9000Btu/h models(A:715, B:250, C:85, D:88)

150mm or more to ceiling

120mm or

more to wall

Left rear side

refrigerant

pipe hole φ65

12000Btu/h models(A:800, B:275, C:100, D:95)

150mm or more to ceiling

120mm or

more to wall

Left rear side

refrigerant

pipe hole φ65

18000Btu/h models(A:940, B:275, C:110, D:100)

Indoor

NOTE:

The wire size of power supply cord and

interconnected wire and the current of

the fuse or switch are determined by the

0.75

maximum current indicated on the

nameplate which located on the side

panel of the unit. Please refer to the

1.5

nameplate before selecting the wire size,

2.5

fuse or switch.

The controller of the air conditioner

designed with a fuse protection function

under abnormal conditions, the

specifications of the fuse have printed on

the circuit board, such as: T3.15A/250VAC,

T5A/250VAC, etc.

Terminal block of indoor unit

L(1)

2(N)

To outdoor unit

Model A

Right

Indoor unit outline

120mm or

more to wall

Right rear side

refrigerant pipe

hole φ65

Indoor unit outline

120mm or

more to wall

Right rear side

refrigerant pipe

hole φ65

Indoor unit outline

120mm or

more to wall

Right rear side

refrigerant pipe

hole φ65

Wall

Outdoor

1(L)

2(N)

To outdoor unit

Model B

Wrong