Casio 2555 Operation Manual - Page 3

Browse online or download pdf Operation Manual for Watch Casio 2555. Casio 2555 5 pages.

Print Page
Operation Guide 2555 2868
To turn an alarm on and off
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Press C twice to move the flashing to the alarm's on/
off setting.
Press C
4. While the on/off setting is flashing, press D to toggle it
Alarm on
twice.
indicator
on (ON) and off (OF).
5. Press A to exit the setting screen.
On/off status
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to scroll through the alarm
screens until the Hourly Time Signal screen (
Hourly time signal
displayed.
on indicator
2. Hold down A until the Hourly Time Signal on/off setting
starts to flash, which indicates the setting screen.
• This operation automatically turns on the Hourly Time
Signal.
3. While the on/off setting is flashing, press D to toggle it
on (ON) and off (OF).
4. Press A to exit the setting screen.
• The Hourly Time Signal on indicator is displayed in all
modes when the Hourly Time Signal is turned on.
On/off status

Date Alert

Date Alert helps you to remember an important date. After you set an alert date
(month and day), a date alert indicator (!) and the current date flash for 24 hours after
the alert date arrives in the Timekeeping Mode. You can set up to five different date
alerts.
Home city time
Alert date
Alert number
(Month – Day)
Date Alert Mode Screen
• To stop the flashing of the date alert indicator and date, use the procedure below to
turn off the alert for that date.
To set the alert date
1. Use C to enter the Date Alert Mode.
2. Use D to scroll through the alert screens until the one
whose date you want to set is displayed.
DA1
3. After you select an alert, hold down A until the month
setting of the alert date starts to flash, which indicates
On/off status
the setting screen.
• This operation automatically turns on the alert.
4. Press C to move the flashing in the sequence shown below.
Alert date
Month
Day
5. While a setting is flashing, use D and B to change it.
• While the month or day setting is flashing, use D (+) and B (–) to change it.
• While the on/off setting is flashing, press D to toggle it on (ON) and off (OF).
6. Press A to exit the setting screen.

Time Recorder

The Time Recorder Mode lets you store up to 50 time
Home city time
entries (hour, minutes, seconds) with the touch of a
button. One way you can use the Time Recorder Mode is
to record the start time and the end time of a particular
event.
• All of the operations in this section are performed in the
Time Recorder Mode, which you enter by pressing C.
To record a Time Recorder time
1. Use C to enter the Time Recorder Mode.
Home city time seconds
• This displays the Time Recorder standby screen.
2. Press D to record the Home City time (hour, minutes,
Standby Screen
seconds).
• The recorded time flashes for about two seconds and then assigned the next
available record number, in the range of
T1
standby screen appears.
• A new time is recorded each time you press D while the standby screen is on the
display.
• The Time Recorder Mode always displays times using 24-hour format, regardless of
the 12-hour/24-hour format setting in the Timekeeping Mode.
SIG
) is
Date alert indicator
Current date (Month – Day)
Timekeeping Mode Screen
DA2
DA3
DA5
DA4
On/Off
through
T50
. Next the time recorder
• Records are assigned numbers sequentially from
• Storing a new time record when there are already 50 records stored in memory
automatically deletes record
T1
, shifts the remaining records upwards by 1, and
stores the new record as
T50
.
To recall Time Recorder times
In the Time Recorder Mode, press A to scroll through
Recorded time
times stored in memory.
• Each press of A scrolls through time records from
(Hour : Minutes Seconds)
higher numbered (newer) records to lower numbered
records.
• Whenever you enter the Time Recorder Mode, the
standby screen appears first.
• Press D to return to the standby screen.
To delete all Time Recorder times
Enter the Time Recorder Mode. While holding down A,
Time record number
press D to delete all Time Recorder times.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
Home city time
• The display range of the stopwatch is 23 hours, 59
Hours
Seconds
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
1/100 second
Stopwatch Mode, which you enter by pressing C.
Minutes
To measure times with the stopwatch
Elapsed Time
D
➤
D
➤
D
Start
Stop
Re-start
Split Time
A
D
➤
A
➤
Start
Split
Split release
( and
flash)
Two Finishes
D
➤
A
➤
D
Start
Split
Stop
First runner
Second runner
finishes.
finishes.
Display time of
first runner.
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
• All of the operations in this section are performed in the Timekeeping Mode, which
you enter by pressing C.
• In the Timekeeping Mode, press D to display the Last Signal screen.
Hour : Minutes Seconds
Month – Day
Press D.
PM
indicator
Day of week
Setting the Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
• When setting the time and date, you can also configure settings for the transmitter,
your Home City code (the code for the city where you normally use the watch),
summer time (Daylight Saving time or DST), auto receive, and the 12/24-hour
format.
To set the time and date manually
1. In the Timekeeping Mode, hold down A until the
transmitter indicator start to flash, which indicates the
setting screen.
2. Press C once to move the flashing to the city code
setting (see the illustration below), and then use B and
D to display the city code you want to use as your
Home City code.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the "City Code
Table".
3. Press C to move the flashing in the sequence shown below to select other settings.
Transmitter
City Code
DST
Day
Month
Year
T1
through
T50
.
➤
D
➤
A
Stop
Clear
➤
D
➤
A
Stop
Clear
A
➤
A
➤
Split release
Clear
Display time of
second runner.
Last Signal Screen
Auto
12/24-Hour
Receive
Format
Seconds
Minutes
Hour
3