Free The Tone COSMIC WAVE Owner's Manual - Page 3

Browse online or download pdf Owner's Manual for Music Pedal Free The Tone COSMIC WAVE. Free The Tone COSMIC WAVE 10 pages. Multiple filtering delay

Print Page

Controls and Indicators

Front Panel

MIX knob/KNOB-L

FEEDBACK knob/KNOB-C

Adjusts the mixing level of the

Adjusts the feedback amount of the

original and delay sounds. Turning

delay. When the Operation screen 2

the knob clockwise increases the

or 3 is shown, the displayed

delay sound level. When the

parameter can be adjusted by this

Operation screen 2 or 3 is shown,

knob.

the displayed parameter can be

adjusted by this knob.

SAVE switch

Press this switch to save the setting.

HOME switch

Press this switch to change the

display. By holding down the switch

for about 2 seconds, the unit enters

Global Function Setup mode.

Display

Preset names and parameters of

each function are shown in this

display.

ON/OFF footswitch

Press this switch to turn on/off the

effect. The LED on the right side of

the footswitch illuminates when ON.

Top Panel

TONE knob/KNOB-R

Adjusts the tone of the delay sound.

When the Operation screen 2 or 3

is shown, the displayed parameter

can be adjusted by this knob.

IN(TRS) terminal

◀ / ▶ Cursor Key

Input terminal to connect an instrument such

Used to page the Menu or Setup

as a guitar/bass or an effect device. For a

screens. The left cursor ◀ key

monaural input, use a cable terminated with

operates as a page backward key

mono phone plugs and for a stereo input,

and the right cursor ▶ key as a

with TRS phone plugs.

page forward key.

DELAY TIME (PARAM) encoder

STEREO

Used to adjust the parameter for

each function. On the HOME screen,

set the preset number to recall.

Turning this encoder when the

NOTE

Operation screen 1 is shown adjusts

In addition to an AC-DC adapter, this unit can be powered by a 9-volt Alkaline battery. Battery life for continuous use (depends on battery

the delay time. When the Operation

type or usage condition): about 2 hours (Alkaline type. Note that a Manganese battery cannot be used due to its short life.)

screen 2 or 3 is shown, the

The display shows "LOW BATTERY" when the battery voltage becomes low. Please exchange the battery or use with an AC-DC adapter.

displayed parameter can be

To exchange the battery, remove the four screws on the bottom plate.

adjusted by this encoder.

Side Panel

PRESET/TEMPO LEDs

These LEDs blink in BPM (tempo)

that has been set. When the preset

1 or 2 is recalled, the correspond-

ing LED illuminates.

TAP footswitch

Used to input TAP tempo. Pressing

this footswitch for 0.5 seconds

recalls presets 1 and 2 alternately.

When using monaural

input and stereo output,

remove the back cover

of the unit and change

MONO

the switch setting from

STEREO to MONO.

EXP/CV/FS terminal

OUT/R terminal

Terminal to connect to an expression

pedal or external footswitch (momentary

Output terminal to connect to an

type). CV (control voltage) is supported.

amplifier or mixer, etc.

OUT/L terminal

Output terminal to connect an

amplifier or mixer, etc. If this unit is

set to be battery driven, inserting a

plug in this jack turns on the power.

DC9V terminal

Power inlet for an AC-DC adapter. This unit can

be powered by an AC-DC adapter having

regulated 9-VDC output, center-minus polarity,

and min. 200 mA current. Use a standard 5.5 x

ø2.1 mm plug.

MIDI IN terminal

Terminal to receive MIDI signal. The

optional CM-3510-TRS (MIDI cable)

is available for this purpose.