Casio CE-T100 Quick Start Manual

Browse online or download pdf Quick Start Manual for Cash Register Casio CE-T100. Casio CE-T100 1 pages.
Also for Casio CE-T100: Service Manual (3 pages)

Print Page
Casio CE-T100 Quick Start Manual
PCR-T465/CE-T100 Quick start guide
IMPORTANT: FOR PROGRAMMING ASSISTANCE PLEASE CALL
TOLL FREE
1-800-638-9228
1 Load the memory protection batteries
1. Un-pack your cash register.
2. Open the printer cover and the platen arm.
3. Open the battery compartment cover.
4. Load 3 new SUM-3 ("AA") type batteries into the compartment. Be
sure that the plus (+) and minus (-) ends of each battery are facing
in the directions indicated by the illustrations inside the battery
compartment.
5. Close the memory protection battery compartment cover back into
place.
Replace memory protection batteries at least once every year.
2 Initialize Your Cash Register
1. Insert the PGM key and turn to the "OFF" position.
OFF
2. Install the 58mm thermal paper roll as illustrated and close printer
cover.
3. Plug the power cord of the ECR into an AC outlet.
The initialization receipt is issued.
Set the key switch to "REG" mode.
3 Setting the Time and Date
Turn the key switch to "PGM" position.
Setting the time.
Example: 1:18PM = 1318
1318x
User's manual
page-7, 8
Hour
Setting the date.
Example: May 19, 2004 = 040519
040519x
Year
Month
4 Setting Tax rates and status
Tax rates
A) If you are in an area that uses a tax table for tax calculation,
Press the / key and select 02 for tax table programming and
follow the instruction.
1. Issue "Help directory report".
User's manual
Select 02 (Tax table programming).
page-9 ~ 11
CAL
X
REG
Z
2. Issue "Tax table index report".
RF
PGM
3. Issue "State tax table code report".
CAL
X
REG
Z
OFF
RF
PGM
User's manual
page-12
REG
OFF
RF
1s
P appears in mode display
PGM
• Enter 4 digits/ • 24 hour format
C
(to end the time setting)
Minute
1s
P appears in mode display
• Enter 6 digits/ • Enter last 2 digits for year set (2004 → 04)
C
(to end the date setting)
Day
User's manual
page-13, 27
/
02/
Select your state.
0101/
Follow these steps.
B) Programming Tax via "Flat Tax" procedure (No break point)
1. Turn the PGM key to the PGM position.
CAL
X
Z
2. Enter the number 3, followed by the s key.
3. Enter 0125 (for tax table 1) followed by the s key. (Enter 0225 for
tax table 2)
4. Enter your tax rate, followed by the F key. Example: For 6%
enter the number 6. For 5.75%, enter 5.75
5. Enter 5002, followed by the F key.
6. Press the s key to end tax programming.
Example: Set Colorado state tax 5.25%
3
s
P appears in mode display
0125
s
Program code number for tax table 1
5^75
F
5.75% tax rate
5002
F
50 for round off and 02 for Add-on
s
(to end the setting)
Tax status
Your cash register is pre-programmed below.
Department 1 ~ 12: taxable 1 & 2
Department 13 ~: non-taxable
If you need other than this setting for the Department and PLUs,
please refer user's manual page-57.
5 Daily Management Report
Read report;
Turn the key switch to the X position and
press F key.
Reset report;
Turn the key switch to the Z position and
press F key.
For more detailed report information, refer user's manual.
For more specific programming options and operating procedures,
that will maximize the benefits of your new cash register, please refer
to you user's manual or call 800/638-9228 for further assistance.
Thank you for your Casio purchase.
CAL
X
REG
Z
OFF
RF
PGM
COLORADO
5.75%
5.75
5002
User's manual
page-43, 74 ~ 79
X
CAL
REG
Z
OFF
F
RF
PGM
X
CAL
Z
REG
OFF
F
RF
PGM