Audiolab 6000N Play User Manual - Page 6

Browse online or download pdf User Manual for Media Converter Audiolab 6000N Play. Audiolab 6000N Play 20 pages.

Print Page

4: Controls and functions - 2

3.Standby Button

When in Standby mode, the power LED will glow in dark red. There are various standby mode

options available. You can activate these options by holding the Standby button for 4 seconds and

then;

- 'Never in auto-standby' mode: short press the Standby button when it ﬂashes once. By default,

6000N Play is set in this mode.

- 'Auto-standby after 20 minutes': short press the Standby button when it ﬂashes twice.

- 'Auto-standby after 1 hour': short press the Standby button when it ﬂashes thrice.

4.Fuse

The fuse speciﬁcation:

220~240V (UK, China, etc.) T630mAL 250V Slow Blow

100~120V (America, Japan, etc.) T1AL 250V Slow Blow

5.AC Mains Socket

You can select between AC mains voltages 115V or 230V using the switch on the underside of the

case. Before connecting the unit to AC mains power, please check that the voltage switch is set to

match to your AC mains voltage.

6.AC Power Switch

Before connecting the AC power cord to the 6000N, please make sure the Power Switch is in the Oﬀ

position. Switch it to the ON position after connecting the unit to the AC mains.

7.Wi-Fi Antenna

DTS Play-Fi is compatible with any router which is authenticated to Wi-Fi standards. We recommend

the use of 802.11n or better which enables 2.4GHz and 5 GHz transmission frequencies. If you have

the option, 5GHz connection will give the most stable performance.

8.Wi-Fi LED State Indicator

Device States

Initialization Mode

Standard Setting Mode

WPS Mode

Network Connecting

Wi-Fi Network Connection

Wired Network Connection

LED States

Fast-ﬂash

Slow-breathe

Double-ﬂash

Slow-ﬂash

Brightly lit

Oﬀ

9.Wi-Fi Setting Button

Press and hold the Wi-Fi Setting Button for 4 seconds to enter WPS mode. Press and hold for 8

seconds to enter the Standard setup mode.

10.Ethernet Port

Use a suitable cable to plug the Ethernet Port to the LAN port of a wireless router for wired

connection.

11.Update Interface

This USB interface is only to be used for upgrading the internal ﬁrmware. It cannot be used for USB

media sources.

Upgrade method: Put the Audiolab upgrade ﬁle on a USB memory stick and insert into the Update

Interface. Hold down the Standby Button on the front panel, turn on the power switch then release

the button. The red LED on the front panel will ﬂash as the upgrade takes place. After the upgrade

completes, a 'relay' sound will be heard and the red LED glows steady and dimly. You can then

unplug the USB stick and operate the 6000N.

12.USB Control Interface

If you are using 6000N with the Audiolab 6000A ampliﬁer, connect this USB Control Interface to the

6000A 'Update' Interface with a USB B data cable. You can then use the Play-Fi APP to control the

listening volume.

Please note: the USB Control Interface cannot be used to link to a PC or output digital music data.

13.12V TRIG Interfaces

Two standard 12V trigger interfaces are provided to allow the 6000N to be switched oﬀ and on

remotely. Connect the 12V trigger source equipment to the 'IN' interface. The 'LINK' interface can

be used as an output to daisy-chain the 12V trigger.

14.Digital Signal Output Interface

Two Digital Signal outputs are provided - one COAX and one OPT (Optical). The maximum output

resolution of the PCM digital signal is 24 bit/192kHz.

15.Analogue Signal Output Interface

Use this stereo output to connect to an ampliﬁer or other device that accepts an analogue input

using a shielded RCA cable.

Page 6