Dura Trel 11116 Assembly Instructions Manual

Browse online or download pdf Assembly Instructions Manual for Outdoor Furnishing Dura Trel 11116. Dura Trel 11116 7 pages. 6' / 7' / 8' picnic table

Print Page
TOOLS NEEDED:
Drill with #2 Phillips Bit,
¼" and 3/32" Drill Bits
2 – 7/16" Wrenches or Sockets
File
TABLE TOP ASSEMBLY
TABLE TOP ASSEMBLY
(Refer to Upper Portion of Drawing 1)
(Refer to Upper Portion of Drawing 1)
On a large flat non-abrasive surface lay the five 1 ½ x 5 ½ x 72/84/96" table top rails (from Box
On a large flat non-abrasive surface lay the five 1 ½ x 5 ½ x 72/84/96" table top rails (from Box
1) out with pilot holes for screws facing up; center rail and the outer two rails have the wood
1) out with pilot holes for screws facing up; center rail and the outer two rails have the wood
inserts. (Table top rails have pilot holes in the center of each rail for top brace.) Make sure wood
inserts. (Table top rails have pilot holes in the center of each rail for top brace.) Make sure wood
inserts are flush with the end of the rails, as they may have shifted in shipment. Set the two 25 ¾"
inserts are flush with the end of the rails, as they may have shifted in shipment. Set the two 25 ¾"
brackets over the pilot holes on each end of the table top rails, leaving a 1/8" gap between rails.
brackets over the pilot holes on each end of the table top rails, leaving a 1/8" gap between rails.
Fasten one bracket to rails with ¾" screws. Repeat for other end of table.
Fasten one bracket to rails with ¾" screws. Repeat for other end of table.
Using the two 7/8 x 1 ½" molded end caps from hardware bag; apply glue to inside edges of caps
Using the two 7/8 x 1 ½" molded end caps from hardware bag; apply glue to inside edges of caps
and place on each end of the 7/8 x 1 ½ x 27" top brace. Lay top brace over the holes in the center
and place on each end of the 7/8 x 1 ½ x 27" top brace. Lay top brace over the holes in the center
of the table top and fasten with 2" screws.
of the table top and fasten with 2" screws.
Apply glue to the inside edges of the 7/8 x 1 ½ x 28" end cap and push (do not slide from end)
Apply glue to the inside edges of the 7/8 x 1 ½ x 28" end cap and push (do not slide from end)
the end cap onto the end of each table top, taking care that the end cap is flush with the outer edges
the end cap onto the end of each table top, taking care that the end cap is flush with the outer edges
of table top.
of table top.
SEAT ASSEMBLY
SEAT ASSEMBLY
(Refer to Lower Portion of Drawing 1) (Make 2)
(Refer to Lower Portion of Drawing 1) (Make 2)
From Box 2, lay out 2 pieces of seat rail with pilot holes facing up and an approximate gap of ⅛"
From Box 2, lay out 2 pieces of seat rail with pilot holes facing up and an approximate gap of ⅛"
between them. Place an 8 ¾" bracket over pilot holes on one end of the seat rails and fasten
between them. Place an 8 ¾" bracket over pilot holes on one end of the seat rails and fasten
bracket to rails with ¾" screws. Repeat on other end of seat. Apply glue to the inside edges of the
bracket to rails with ¾" screws. Repeat on other end of seat. Apply glue to the inside edges of the
⅞ x 1 ½ x 11 ⅛" end caps and push onto the ends of the seat rails.
⅞ x 1 ½ x 11 ⅛" end caps and push onto the ends of the seat rails.
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
#11114/11115/11116
6' / 7' / 8' P
ASSEMBLY INSTRUCTIONS
T
ICNIC
ABLE