DANLERS CBU-HBWD IP66 Quick Manual

Browse online or download pdf Quick Manual for Security Sensors DANLERS CBU-HBWD IP66. DANLERS CBU-HBWD IP66 2 pages. Ip66 rated ceiling high bay (wide) passive infra red (pir) occupancy detector & photocell

Print Page

CBU-HBWD IP66

IP66 Rated Ceiling High Bay (Wide) Passive

Infra Red (PIR) Occupancy Detector & Photocell

Input: 220-240 Vac 50Hz

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT

NOTE: CBU-HBWD IP66 is only compatible to work with CASAMBI enable equipment

This CBU-HBWD IP66 High Bay

(Narrow Detection) Lighting Control

has an IP66 rated weatherproof

enclosure and can be ceiling

mounted. Conﬁ gurable via the free

to download Casambi APP on

Google Play or Apple APP Store.

INSTALLATION

To be installed by a competent person with

reference to BS 7671 or equivalent local standards.

If in doubt consult a qualiﬁ ed electrician.

• Plan where the CBU-HBWD IP66 is to be

located (see diagram 1). Switch off supply and

check for hidden cables and pipes.

• Remove the front cover by quarter turning the

four quick release fasteners to the '0' position

(see diagram 4 overleaf).

• Mount the back section of the mounting box in

the required location via the 4 corner holes.

• Thread mains cable carefully through the

required membrane entry point.

• Unclip the internal back plate. Remove the

required knock out if replacing the optional

internal back plate.

• Thread mains cable into the unit. The CBU-

HBWD IP66 should be connected as shown in

diagram 2:

L - Live in. N - Neutral in.

• Reclip the internal back plate if required.

• Replace the front cover ensuring the quick

release fasteners are secured in the '1' position.

OPERATION

To check the operation of the CBU-HBWD IP66:

• Turn on the supply then after 20 seconds if the

sensor has recognised movement of a person

within its zone of detection the integral red LED

on CBU-HBWD IP66 will stay illuminated for 4

seconds before the red LED turns off.

• Thereafter, every time movement is detected by

CBU-HBWD IP66 the integral red LED will stay

illuminated for 4 seconds.

The control also features adjustable time out (time

lag) control and daylight threshold control which

are conﬁ gured by the Casambi APP.

PRECAUTIONS

• Do not place the CBU-HBWD IP66 near heat

sources, fans or in ventilated ceiling voids.

• CBU-HBWD IP66 can be wired in parallel

(sharing the same Live and Neutral).

• Do not place close to, or positioned such

that, any light source points directly into the

CBU-HBWD IP66.

• Ensure wires and cables are securely held within

the connection terminals.

• The CBU-HBWD IP66 should be protected by a

5 or 6 Ampere mcb or fuse.

• Disconnect the CBU-HBWD IP66 from the

circuit before performing insulation testing

of the wiring circuit.

DANLERS Limited, Vincients Road, CHIPPENHAM, Wiltshire, SN14 6NQ, UK.

Telephone: +44 (0)1249 443377 Fax: +44 (0)1249 443388 E-mail: [email protected]

www.danlers.co.uk

Company Registered Number 2570169 VAT Registration Number 543 5491 38

01/03/18

TECHNICAL DETAILS

INPUT

Voltage:

220 - 240Vac

Frequency:

50Hz

Max. mains current:

0.05A

Standby current:

0.05A

RADIO TRANSCEIVER

Operating frequencies:

2.4... 2,483 GHz

Max. output power:

+4 dBm

LUX PARAMETERS

Range:

5 - 2000 lux

OPERATING CONDITIONS

Note: The temperature difference between the

detection target and the background must be

at least 4 °C.

Max. case

+70 °C

temperature:

Storage temperature:

-25... +75 °C

Max. relative humidity:

0... 80%, non cond.

CONNECTORS

Terminal block

0.5mm

Wire size:

solid or stranded

Wire strip length:

6-7mm

Tightening torque:

0,4 Nm/4 Kgf.cm

MECHANICAL DATA

110mm x 110mm x

Dimensions:

73mm

Weight:

255g (unpacked)

Degree of protection:

IP66

Protection class:

Built-in Class 2

Flame-retardant

Material (casing)

polycarbonate/

Polypropylene.

Finish / Colour

Matt /Grey (RAL 7035)

Protection class:

Built-in Class 2

CONFORMITY AND STANDARDS

EN60669-2-1:2004

EMC emission:

inc. A12:2010

EN60669-2-1:2004

EMC immunity:

inc. A12:2010

EN60669-2-1:2004

Safety:

inc. A12:2010

Complies with WEEE

Environment:

and RoHS directives

5 YEAR WARRANTY

CBU-HBWD IP66 comes with a 5 year

warranty from the date of manufacture

and is CE marked.

- 2.5mm

Suggested typical wiring

230Vac

5A or 6A MCB

or fuse

L - Live in. N - Neutral in.

Two neutral and two live terminals

are available for easy 'loop in' and

'loop out' connection.

plan

110

Mounting height

up to 14m

Perspective view -

ceiling mounted

Up to

28m diameter

DIAGRAM 1

DIAGRAM 2

side

110

DIAGRAM 3

INS369 CBU-HBWD IP66