Elsner WS1000 Color First Steps
Browse online or download pdf First Steps for Control Systems Elsner WS1000 Color. Elsner WS1000 Color 2 pages. Connect control system
Also for Elsner WS1000 Color: Assembly Information (2 pages), Manual (2 pages)
Print Page
EN
WS1000 Connect Control System:
First steps
Item numbers
60241-60246
The manual with additional information about commissioning,
functions and use of the controls WS1000 Connect can be
downloaded from www.elsner-elektronik.de.
1.
Description
The various technical facilities installed in the building are controlled automatically
and operated manually using the Control System WS1000 Connect. In order
to be able to set up the system flexibly, both cable connections and wireless chan-
nels are available.
The WS1000 Connect is delivered as a set, which includes the sensors needed
for room climate and weather data as well as the central unit (display with control
electronics). The sensor values are shown in the display and are the basis of the
automatic controls.
Functions and properties of the central unit WS1000 Connect:
•
Colour touch display 10.1 inch, for manual operation, system set up and
for setting the basic and automatic functions
•
Network connection by LAN or WLAN
•
Browser for viewing websites, etc.
•
Remote access via network for system setup, diagnostics etc. Approval by
the user required
•
Slide show from SD card as screen saver
•
Data storage on SD card (storage of settings)
•
Integrated loudspeaker (4 tweeters, 1 broadband speaker)
•
Individually settable presence simulation
•
Motor outputs (4-10 pcs, depending on model) for electrically powered
- Awnings, blinds, shutters
- Windows/sliding roofs
•
4 multifunction outputs for
- Lights (on/off)
- Dimmer of one light
- Heating (on/off), cooling (on/off), ventilators (on/off)
- Alarms
- Gutter heating
•
16 scenes for calling individually set movement positions and switch states
With a scene, several motors and devices are addressed simultaneously so
a suitable ambience is created with one press of a button ("TV", "Eating",
etc.).
•
4 multifunction inputs for
- Motion detector
- Smoke detector
- Climate detector (prevent ventilation if external
air-conditioning/heating is active)
- Safety contact (motors in safe position,
prevent exhaust air, start incoming air)
- Impulse for automatic reset
- Binary contact for free use
•
10 key inputs for additional conventional wind sensor for operating
motors and devices on site
•
32 radio channels for devices with Elsner RF radio protocol
- Sensors WGTH-UP for room temperature, humidity (from version 1.3),
WG AQS/TH-UP for room temperature, humidity, CO
WGT (indoor temperature) for measuring at other locations in the room
- Remote control Remo 8 (from version 1.8), Remo pro
- Sensor Corlo P RF, sensor interface RF-B2-UP
- WL400, WL800 and WL-Z ventilation units
- RF-VM ventilation module for connecting fans/circulation air heaters
from other manufacturers
- Wireless relay RF relay for on/off (each from version 5.5),
Heating module RF-HE-ST (from version 5)
- Wireless motor control device RF-MSG for up/down (from version 3.7)
- RF-L wireless dimmer:
The wireless actuators with a production date after 14.01.2016 are compatible with
the WS1000 Connect system. The production date can be found as part of the
serial number which has the following structure "DD MM YY consecutive number".
WARNING!
The radio transmission takes place over a non-exclusively
available transmission channel!
The device is not suited for applications outside the field of safety
equipment, such as emergency stop and alarm equipment.
Functions and properties of the indoor sensor:
•
Temperature measurement
•
Humidity measurement
Functions and properties of the weather station:
•
Brightness measurement (sun sensor)
•
Temperature measurement
•
Wind speed measurement
•
Precipitation detection
•
GPS receiver for date/time and installation coordinates (for sun position
calculation)
Overview of connection and control options
Scope of delivery
•
Central control and operating unit with flush installation box and installation
accessories
•
SD card in card slot
•
Weather station with connection accessories
•
Indoor sensor with frame
(In addition, you need a device socket ø 60 mm, 42 mm deep)
2.
Commissioning
Installation, testing, operational start-up and troubleshooting should
only be performed by an authorised electrician.
DANGER!
Risk to life from live voltage (mains voltage)!
There are unprotected live components inside the device.
• Inspect the device for damage before installation. Only put undamaged
devices into operation.
• Comply with the locally applicable directives, regulations and provisions
for electrical installation.
• Immediately take the device or system out of service and secure it against
unintentional switch-on if risk-free operation is no longer guaranteed.
Use the device exclusively for building automation and observe the operating ins-
tructions. Improper use, modifications to the device or failure to observe the ope-
rating instructions will invalidate any warranty or guarantee claims.
Operate the device only as a fixed-site installation, i.e. only in assembled condition
and after conclusion of all installation and operational start-up tasks, and only in
the surroundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may
occur after publication of these operating instructions.
,
2
Procedure for commissioning
1. The installation of the Control System and the sensors must be performed by
a skilled electrician. Information in the installation instructions, for example
also about the installation location, must be observed.
2. After completing the installation work, the Control System must be thoroughly
set up in the menu System > Installation. Which connections are used for
which functions, e.g. Motor 1 = Awning, is specified here.
See manual chapter Basic setting.
3. More settings for time reception, screen saver, network connection, access
code, updates, etc. can be made at any time in the menu System > WS1000 set-
tings.
See manual chapter Basic setting.
Control System WS1000 Connect • from software 02.02 • Version: 30.01.2023 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de • Technical Service: +49 (0) 7033 / 30945-250
Control System WS1000 Connect
4. The automatic functions must be adjusted in the menu System > Automatic
settings to the structural conditions and individual requirements of the users.
See manual chapter Automatic.
Operating system
The WS1000 Connect works with the Android operating system. However, the
Control System work self-sufficiently and therefore no third-party Apps may be in-
stalled!
Protective film
Remove the protective film from the display. Otherwise, there is a risk that the
touch operation will be deactivated. If this should happen, the control system must
be restarted so that the touch display works again.
3.
Overview of homepage, navigation
With the Control System WS1000 Connect you can control the connected tech-
nology centrally, e.g. raise and lower shades, switch devices on and off and dim
lights. All the settings are also made on the display.
Top menu bar
Menu
Bottom navigation menu
Top menu bar:
The Internet browser (open website) and Volume functions can be accessed at any
time via the top menu bar. Time and date are displayed. Additionally, the start key
for the slide show appears here as soon as an SD card with pictures is loaded.
Menu on left (Start menu):
The menu on the left-hand side contains the System menu, with which you can re-
ach all the basic and automatic settings.
Connected motors and devices are operated by hand using the Manual menu.
The menu item Presence simulation is displayed in the start menu depending on
the setting. The presence simulation can be switched on or off there.
This includes the selected Favourites for manual operation and the websites saved
as Bookmarks.
So that a motor/device is displayed in the Manual menu and/or as a Favourite, the
display has to be activated in the setting "Manual menu" in the installation settings.
System > Installation > Motor/Multif.output > Manual menu
Right-hand display and settings area:
The control unit displays the current weather data as its start page .
The functions / parameters are displayed here when navigating in the settings
(submenus).
Bottom navigation menu:
On the bottom edge of the display you will see a Navigation menu with "Back"
arrow and a circle, which takes you back directly to the start page. Stay longer on
the circle to activate the screen saver.
Move motors and switch devices
Additional information about the display and control possibilities is contained in
Operation.
Example: Move blinds manually
Start menu > Manual
Sliding bar position
Selecti-
on
Example: Switch light
Start menu > Manual
1
Display
and
setting
area
Position
informa-
tion
Control
buttons