Dustbane Hurricane Mini Quick Manual - Page 2

Browse online or download pdf Quick Manual for Vacuum Cleaner Dustbane Hurricane Mini. Dustbane Hurricane Mini 2 pages.

Print Page

DAILY MAINTENANCE

Clean the dirty water tank.

Clean the dirty

water tank.

Check that the

brush is clean.

Check that the

squeegee is clean

Make sure the squeegee is

squeegee is clean

and the blades are not

Check that the

and the blades are not

clean and the blades are not

and the blades are not

worn.

squeegee is clean

worn.

and the blades are not

worn.

•

unscrew the nuts fixing the blade retainers;

•

unscrew the nuts fixing the blade retainers;

REPLACING THE SQUEEGEE BLADES

•

unscrew the nuts fixing the blade retainers;

•

remove the two blade retainers;

•

unscrew the nuts fixing the blade retainers;

•

remove the two blade retainers;

•

remove the two blade retainers;

•

remove the blade;

•

remove the blade;

•

remove the two blade retainers;

•

remove the blade;

•

put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;

•

put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;

•

remove the blade;

•

put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;

•

put the two blade retainers back on the squeegee and screw up the nuts again;

•

put the two blade retainers back on the squeegee and screw up the nuts again;

•

unscrew the nuts fixing the blade retainers;

put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;

•

put the two blade retainers back on the squeegee and screw up the nuts again;

•

put the two blade retainers back on the squeegee and screw up the nuts again;

•

remove the two blade retainers;

•

remove the blade;

•

put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;

•

put the two blade retainers back on the squeegee and screw up the nuts again;

Attaching the brush:

•

rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring it with the brush cover. Action the drive lever repeatedly until the brush

•

Attaching the brush:

engages..

•

Removing the brush:

engages..

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

Removing the brush:

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

Unscrew the wing nuts fixing the blade retainer.

Attaching the brush:

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

•

engages..

Removing the brush:

Remove the blade retainer.

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush is released and falls to the ground.

Remove the blade.

Put the same blade back, reversing the edge in

contact with the floor, or replace with a new one.

Reposition the blade retainer and fix the wing nuts

back.

PLDC01957

Dustbane Products Ltd., 1000 Last Mile Dr., Ottawa, ON K1G 6Y1 • Tel: 1-800-387-8226 Fax: 1-800-363-5309 www.dustbane.ca

DAILY MAINTENANCE

Check the dirty water tank float

Make sure the dirty water tank

is undamaged and clean and

float is undamaged and clean

moves freely on the pin.

and moves freely on the pin.

BATTERY

CHARGER ON

BATTERY

CHARGER ON

BOARD

CHARGER ON

BOARD

BATTERY

CHARGER ON

BOARD

REPLACING THE SQUEEGEE BLADES

•

unscrew the nuts fixing the blade retainers;

•

remove the two blade retainers;

REPLACING THE SQUEEGEE BLADES

•

remove the blade;

•

put the same blade back, reversing the edge in contact with the floor until all four edges are worn, or replace with a new one;

•

put the two blade retainers back on the squeegee and screw up the nuts again;

ATTACHING/REMOVING THE BRUSH

Attaching the brush:

•

rest the brush on the floor in front of the machine. Raise the front of the machine by levering on the handle, then lower it onto the brush, centring

engages..

Removing the brush:

ATTACHING/REMOVING THE BRUSH

•

Raise the front of the machine by levering on the handle, then operate the brush lever repeatedly. After operating the lever a few times, the brush

PLDC01957

Check that the

Make sure detergent outlet

Check that the

detergent outlet filter

filter is clean and free of

detergent outlet filter

Clean the dirty

detergent outlet filter

is clean.

water tank.

debris.

is clean.

TO CHARGE BATTERIES

Plug in On Board charger to

charge batteries if equipped.

NOTE: Never stop charge until

cycle is complete (green light).

Check that the

squeegee is clean

and the blades are not

worn.

ATTACHING/REMOVING THE BRUSHES

Position the brush underneath the head, in the centre (single-

brush floor scrubber), position the brushes underneath the

head on both sides (double brush scrubber), switch the

machine on.

ON-OFF

Press the

releases brush attachment. The button is only enabled when

all the functions are deactivated (suction motor and brushes).

DAILY MAINTENANCE

Make sure the brushes/drive

Check that the

Check the dirty water tank float

Check that the

pad are clean and not worn

brush is clean.

is undamaged and clean and

brush is clean.

out. Replace if necessary.

moves freely on the pin.

BATTERY

CHARGER ON

BOARD

REPLACING THE SQUEEGEE BLAD

ATTACHING/REMOVING THE BRUS

switch, once after starting the machine

Check that the

Check that t

detergent outle

brush is clean.

is clean.