Datalogic S62-PA-2/5 Instruction Manual - Page 4

Browse online or download pdf Instruction Manual for Accessories Datalogic S62-PA-2/5. Datalogic S62-PA-2/5 4 pages.

Print Page

S62...M

Background suppression

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (yellow)

The yellow LED ON indicates that the N.O. output is closed and the N.C.

output is open.

STABILITY LED (green) (S62...M2/M3)

When permanently ON, the green LED indicates a normal operating condition

where the received signal has a safety margin superior to 30% respect to the

output switching value. The sensor is ready to function correctly (stability

condition).

POWER ON LED (green) (S62...M0/M1)

The green LED ON indicates the powering status and the laser emission

presence.

DISTANCE ADJUSTMENT TRIMMER (ADJ.)

A 6-turn trimmer allows the background suppression distance adjustment

through a mechanical variation of the optic triangulation angle.

The operating distance increases, rotating the screws in a clockwise direction.

Please refer to the "SETTING" paragraph for acquisition or setup procedure

indications.

POSITION INDICATOR

This indicator presents a scale numbered from 1 to 6 that allows a precise

adjustment of the suppression distance in the entire operating range.

Please refer to the "SETTING" paragraph for use indications.

TIMER ADJUSTMENT TRIMMER (S62...M05/M15/M25/M35)

This control allows to vary the output delay deactivation from 0 to 1 sec.

Please refer to "TIMER FUNCTIONS" paragraph for use indications.

DARK/LIGHT TRIMMER (S62...M01/M11-PN)

The LIGHT/DARK mode is selected using a mono-turn trimmer.

LIGHT MODE: clockwise rotation

DARK MODE: counter-clockwise rotation.

WARNING: the maximum mechanical rotation range of the trimmer is 240°.

Do not force over of the maximum and minimum positions.

INSTALLATION

The sensor can be positioned by means

of the three housing's holes using two

screws (M4x25 or longer, 1.5Nm max.

tightening torque) with washers.

Various orientable fixing brackets to

ease the sensor positioning are available

(please refer to the general catalogue).

The operating distance is measured

from the front surface of the sensor

optics.

The M12 connector can be oriented at two different positions using the

specific fastening spring and rotating the block of 180°.

CONNECTIONS

S62-PA-2/5...PN

S62-PA-2...PP/NN

S62-PA-5...PP/NN (M12 connector)

S62...M0-PP/PN/NN

Power supply:

Ripple:

Consumption

(output current excluded):

Outputs:

S62...PP/NN: PNP or NPN N.A./N.C. 30 VDC / S62...PN: NPN/PNP; 30 VDC max (short-circuit protection)

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Emission type:

Spot dimension:

6x6 mm (at 200 mm)

Operating distance (typical values):

30...300 mm

Adjustment:

Multiturn distance adjustment trimmer / Timer adjustment trimmer (S62...M05/M15/M25/M35)

DARK/LIGHT selection:

mono-turn trimmer (S62...M01/M11-PN)

Difference (90% white / 4% black):

< 8 %

Hysteresis (90% white):

Indicators:

OUTPUT LED (YELLOW) / STABILITY LED (GREEN)

Operating temperature:

Storage temperature:

Dielectric strength:

Insulating resistance:

Ambient light rejection:

Vibrations:

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

UL requirements:

they are intended to be connected to a Class 2 transformer or class 2 power supply

Weight:

Suppression distance setting

1. Object detection

Position object to detect in front of the sensor at the distance required.

Turn distance adjustment trimmer (ADJ) to minimum: yellow LED OFF and

green LED ON.

Rotate trimmer in a clockwise direction until the yellow LED and green LED

turn ON. Object detection condition (A status of position indicator)

2. Background suppression

Remove object and ensure that the background is in front of the sensor:

yellow LED OFF and green LED ON.

Rotate trimmer in a clockwise direction until the yellow LED and green LED

turn ON: background detection condition (B status of position indicator).

The trimmer reaches maximum level with yellow LED OFF if the background

is outside the operating range.

TECHNICAL DATA

S62...M1-PP/PN/NN

S62...M2-PP/PN/NN

10 ... 30 VDC

2 Vpp max.

40 mA max.

100 mA (overload and overvoltage protection)

 2 V

500 s

1 ms

1 kHz

500 Hz

RED (660 nm)

INFRARED (880 nm)

15x15 mm (at 400 mm)

60...600 mm

60...1200 mm

< 12 %

< 25 %

< 5 %

OUTPUT LED (YELLOW) / POWER ON LED (GREEN)

-10 ... 55 °C

-20 ... 70 °C

500 VAC 1 min., between electronics and housing

>20 M 500 VDC, between electronics and housing

According to EN 60947-5-2

0.5 mm amplitude, 10 ... 55 Hz frequency, for each axis (EN60068-2-6)

11 ms (30 G) 6 shock for each axis (EN60068-2-27)

ABS

PMMA window; PC lens

IP67

2 m cable  4 mm / M12 4-pole connector

90 g. max. cable vers. / 40 g. max. connector vers.

SETTING

Rotate trimmer in an anticlockwise direction until yellow LED turns OFF

and green LED ON: condition where background is outside operating

range (C status of position indicator).

3. Setting and control

Rotate trimmer in an anticlockwise direction until the indicator reaches

an intermediate point between position A and C.

If position A and C are close to each other, leave trimmer on position C.

The sensor is now ready to function correctly and in stable conditions:

DETECTION DIAGRAM

S62...M3-PP/PN/NN

1,5 ms

330 Hz

200x200 mm (at 2000 mm)

200...2000 mm

(recommended target 400x400mm)

< 30 %

< 20 %

TIMER ADJUSTMENT

TRIMMER (mod.M05/M15/M25/M35)

DARK/LIGHT

TRIMMER

(S62-M01/M11-PN)

6.18

10.7

OUTPUT LED

STABILITY LED (S62...M2/M3) /

STABILITY LED

POWER ON LED (S62...M0/M1)

TIMER FUNCTION (S62...M05/M15/M25)

The timer function allows to adjust the output deactivation delay when the

object is outside the detection area. The delay extends the output activation

allowing the slower interface systems to detect shorter pulses.

The delay adjustment is carried-out manually using the Timer adjustment

trimmer. Clockwise rotation increase the delay from 0 to a max. 1 sec. value.

The sensors are NOT safety devices, and so MUST NOT be used in the safety control of the machines

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com: Contact Us, Terms and Conditions, Support.

The warranty period for this product is 36 months. See General Terms and Conditions of Sales for

further details.

Under current Italian and European laws, Datalogic is not obliged to take care of product

disposal at the end of its life. Datalogic recommends disposing of the product in compliance with

local laws or contacting authorised waste collection centres.

rights under copyright, no part of this documentation may be reproduced, stored in or introduced into a

retrieval system, or transmitted in any form or by any means, or for any purpose, without the express

written permission of Datalogic S.p.A. and/or its affiliates. Datalogic and the Datalogic logo are registered

trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. All other trademarks

and brands are property of their respective owners. Datalogic reserves the right to make modifications

and improvements without prior notification.

DIMENSIONS

4.7

RECEIVER

EMITTER

M12

Ø15

CABLE VERSION

18.4

DISTANCE ADJUSTMENT TRIMMER

POSITION INDICATOR

where installed.

826002875 Rev. G