Fright Ideas PicoBoo JR Quick Start Manual - Page 2

Browse online or download pdf Quick Start Manual for Controller Fright Ideas PicoBoo JR. Fright Ideas PicoBoo JR 2 pages.

Print Page
Fright Ideas PicoBoo JR Quick Start Manual
Relay Output Wiring
• Each output can handle up to 10 amps at 120VAC, 5 amps at 220VAC, or 5 amps at 30 VDC.
!
• The terminal blocks can be removed by pulling them out in the direction the wires exit the block.
• If you'd like the device to stay on by default and turn off when the output is energized use NC instead of NO.
12 VDC
DEVICE
BEACON
LED LIGHT
MAGLOCK
-
+
IN
1
2
POWER
/ INPUT
OUTPUTS
ANY 12 VDC DEVICE
ANY VOLTAGE
DEVICE
TO POWER SUPPLY
APPROPRIATE
1
2
FOR DEVICE
OUTPUTS
ANY DEVICE THAT'S NOT 12 VDC
BLUE = FAST
GREEN = SLOW
USE A 12V 5A POWER
SUPPLY FOR THE
PICOBOO.
-
+
IN
1
2
POWER
/ INPUT
OUTPUTS
12 VDC MOTOR ON/OFF IN ONE DIRECTION
FOG
MACHINE
FOG
SEE OUR WEBSITE FOR A COMPATIBLE
HIGH
FOG MACHINE CABLE SO YOU DON'T HAVE
VOLTAGE
TO HACK YOUR REMOTE.
OR
1. UNPLUG FOG MACHINE
2. OPEN REMOTE
3. LOCATE FOG BUTTON PINS
1
2
4. SOLDER A WIRE TO EACH PIN
OUTPUTS
5. CONNECT THOSE WIRES AS
SHOWN
FOG MACHINE
12 VDC
12 VDC
DEVICE
DEVICE
-
+
IN
1
2
POWER
/ INPUT
OUTPUTS
TWO 12 VDC DEVICES
HIGH
VOLTAGE
TO WALL
OUTLET
TAKE APPROPRIATE
!
SAFETY PRECAUTIONS
WHEN WIRING HIGH
VOLTAGES.
1
2
OUTPUTS
ANY 110 VOLT LOAD
BLUE = FAST
GREEN = SLOW
USE A 12V 5A POWER
SUPPLY FOR THE
PICOBOO.
-
+
IN
1
2
POWER
/ INPUT
OUTPUTS
12 VDC MOTOR FORWARD AND REVERSE
TO WALL
OUTLET
12 VDC
DEVICE
HIGH
VOLTAGE
-
+
IN
1
2
POWER
/ INPUT
OUTPUTS
ONE 110 VOLT DEVICE, ONE 12 VDC DEVICE
Trigger Input Wiring
By default, the animation will play once
when the trigger is activated. If the trigger is
!
still active when the animation ends it will
loop. Enable "Single Shot" mode if you
want to prevent looping.
SENSOR WIRES
BLACK
GND (-)
RED
12VDC (+)
WHITE
RELAY C
GREEN
RELAY N.O.
-
+
IN
POWER
NOTE: PIR SENSORS CAN TAKE UP TO A
/ INPUT
MINUTE TO "WARM UP". DURING THIS TIME
THE PICOBOO'S YELLOW INPUT LIGHT WILL
FLASH.
PIR MOTION SENSOR
SENSOR WIRES
BLUE
GND (-)
-
+
IN
BROWN
12VDC (+)
POWER
WHITE
RELAY C
/ INPUT
BLACK
RELAY N.O.
BEAM SENSOR
C
RELAY
OUTPUT
N.O.
POWER
BASE STATION
CONNECT THESE ONLY
-
+
IN
IF THE BASE RUNS ON
POWER
12 VDC AND DOES NOT
/ INPUT
HAVE ITS OWN POWER
SUPPLY CONNECTED.
REMOTE
WIRELESS TRIGGER
Toggling Single Shot Mode
1. Hold the middle 1 button while powering up the PicoBoo.
2. Keep holding the 1 button for about 10 seconds until the
light above it comes on and stays on, then let go.
Repeat the same steps to disable.
PRESSURE MAT
-
+
IN
PUSH BUTTON
POWER
/ INPUT
PRESSURE MAT OR PUSHBUTTON
LOOPED WITH
ON/OFF OPTION
SWITCH
LOOPED
-
+
-
+
IN
IN
POWER
POWER
/ INPUT
/ INPUT
CONTINUOUS PLAY (LOOPED)
TO TRIGGER
CONNECT THE TRIGGER AS
SHOWN IN ONE OF THE
-
+
-
+
IN
IN
OTHER DIAGRAMS.
POWER
POWER
CONNECT ADDITIONAL
/ INPUT
/ INPUT
PICOBOOS TO THE FIRST
PICOBOO AS SHOWN.
ADDITIONAL
FIRST
PICOBOO
PICOBOO
MULTIPLE PICOBOOS WITH ONE TRIGGER