Frigidaire CFHT1843LS4 Use & Care Manual - Page 8
Browse online or download pdf Use & Care Manual for Refrigerator Frigidaire CFHT1843LS4. Frigidaire CFHT1843LS4 14 pages. Electrolux
Print Page
Toavoid electric shock, which cancause deathor
severe personal injury, d isconnect therefrigerator from
electrical power b efore connecting a watersupply lineto
ToAvoid Property D amage:
• Copper orStainless Steel braided t ubing isrecommended
forthewater s upply line.Water s upply t ubing made of
1/4 inchplastic i snotrecommended
to beused. P lastic
tubing greatly i ncreases thepotential forwaterleaks, and
themanufacturer
willnotberesponsible foranydamage
if plastic t ubing isused forthesupply line.
DONOT install w atersupply tubing in areas where
temperatures fall below freezing.
Chemicals froma malfunctioning softener c andamage
theicemaker. If theicemaker i sconnected to soft
water, e nsure thatthesoftener i smaintained a nd
Ensure t hatyourwatersupply lineconnections comply
withall local p lumbing c odes.
Before Installing
The Water Supply Line, You Will Need:
-
Basic Tools: adjustable wrench, flat-blade screwdriver,
and Phillips
TM
screwdriver
Access to a household cold water line with water
pressure between 30 and 100 psi.
A water supply line made of 1/4inch (6.4 mm) OD,
copper or stainless steel tubing. To determine the
length of tubing needed, measure the distance
from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add
approximately 7 feet (2.1 meters), so the refrigerator
can be moved out for cleaning (as shown).
A shutoff valve to connect the water supply line to your
household water system. DO NOT use a selFpierdng
type shutoff valve.
A compression nut and ferrule (sleeve) for connecting
a copper water supply line to the ice maker inlet valve.
To Connect Water Supply Line To Ice Maker [nlet Valve
1.
Disconnect refrigerator from electric power source.
2.
Place end of water supply line into sink or bucket.
Turn ON water supply and flush supply line until
water is clear. Turn OFF water supply at shutoff valve.
3.
Remove plastic cap from water valve inlet and
discard cap.
4.
If you use copper tubing - Slide brass compression
nut, then ferrule (sleeve) onto water supply line.
Push water supply line into water valve inlet as far
as it will go (1/4 inch / 6.4 mm). Slide ferrule (sleeve)
into valve inlet and finger tighten compression nut
onto valve. Tighten another half turn with a wrench
DO NOT over tighten. See Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing. Slide
compression nut onto valve inlet and finger tighten
compression nut onto valve. Tighten another half turn
with a wrench; DO NOT over tighten. See Figure 2.
5. With steel clamp and screw, secure water supply line
(copper tubing only) to rear panel of refrigeratDras shown.
6.
Coil excess water supply line (copper tubing only),
about 21/2turns, behind refrigerator as shown and
arrange coils so they do not vibrate or wear against
any other surface.
7. Turn ON water supply at shutoff valve and tighten
any connections that leak.
8.
Reconnect refrigerator to electrical power source.
9.
To turn ice maker on, lower wire signal arm (side
mounted) or set the ice maker's On/Off power
switch to the "T'
position (rear mounted).
_Steel
Clamp
Brass
Compression
Ferrule
Copper
water line
er VaJve
Bracket
Include
enough
tubing
in
loop
to
allow
moving
refrigerator
out
for
cleaning.)
I
_Steel
Clamp
I
I
'_i]
Steel
V/
_
_---Valve
Inlet
_at_r
Valw
-- 6 ft. Stainless
Steel
water
line
ousehold water supply
Figure 1
Figure 2
Check with your local building authority for recommendations
on water lines and associated materials prior to installing
your new refrigerator, Depending on your local/state
building codes, Frigidaire recommends for homes with
existing valves itsSmart Choice® water line kit 5305513409
(with a 6 ft. StainlessSteel Water Line) and for homes
without an existing valve, Frigidaire recommends its Smart
Choice wateP line kit 5305510264 (with a 20 ft. Copper
Water Line with self-tapping saddle valve). Pleaserefer to
vwvw.frigidaire.com/store for more information.
After connecting the water supply, refer to "How to Prime
the Water Supply System" for important information about
priming an empty water supply system.
Your refrigerator'swater supply system includes severaltubing
lines, a water filter, a water valve, and a water tank. To ensure
that your water dispenser works properly, this system must
be completely filled with water when your refrigerator is first
.........
_n
_ the h_ho!d
................................................