Agri-Fab 190-653B Owner's Manual - Page 7
Browse online or download pdf Owner's Manual for Outdoor Cart Agri-Fab 190-653B. Agri-Fab 190-653B 12 pages. Utility carts
Print Page
18. Assemble an axle clip, a flat washer, a wheel with the
valve stem facing out, and another flat washer onto
each end of the axle. Place an additional flat washer on
each end of the axle if there is space for it. Secure each
wheel on the axle with a cotter pin, spreading the ends
of the pin around the axle. Press a hub cap onto the flat
washer on each end of the axle. See figure 13.
WHEEL
FLAT
WASHER
HUB CAP
COTTER PIN
FIGURE 13
19. Turn cart over so that it rests right side up on its
wheels.
20. Assemble the end of the hitch bracket (two holes) down
through the slot at the front of the drawbar tongue.
Fasten it to the tongue using the 3/8" x 1" hex bolt and
3/8" nylock nut. Tighten. See figure 14.
21. Assemble the hitch pin through the hitch bracket and
the tongue and secure with the 1/8" hair cotter pin. See
figure 13.
HITCH
BRACKET
1/8" HAIR
COTTER
PIN
FIGURE 14
22. Place the tailgate down into the tailgate guides so that
the holes in the bottom lip of tailgate fit over the truss
head bolts in the bottom of the cart. This completes the
assembly of your cart.
AXLE
AXLE CLIP
FLAT
WASHER
HITCH PIN
3/8" x 1"
HEX BOLT
TONGUE
3/8"
NYOCK
NUT
OPERATION
CAUTION: VEHICLE BRAKING AND
STABILITY MAY BE AFFECTED wITH THE
ADDITION OF AN ACCESSORY OR AN
ATTACHMENT. BE AwARE OF CHANGING
CONDITIONS ON SLOPES.
1. Refer to the vehicle owners manual for instructions about
safe operation on slopes.
2. Use the slope guide provided on page 11 of this
manual to determine if slope angle is too steep for safe
operation.
3. For best handling and traction, distribute the weight of
the load evenly in the cart.
4. Always test to make sure your tractor has adequate
towing and braking capabilities whenever hauling a
substantial amount of weight in your cart. Use extra
caution when operating on slopes.
DO NOT EXCEED wEIGHT CAPACITY OF CART
One cubic foot of dirt weighs approximately 80 lbs.
5. To dump material from the cart, remove the tailgate by
lifting it straight up and out from between the guides.
Release the spring latch on the tongue by pulling the
latch lock lever forward, away from the cart. The cart
bed will then tilt backwards to empty its contents. After
emptying, pull the front of the bed down toward the cart
tongue until the latch snaps into place. Replace the
tailgate if desired.
6. The maximum towing speed for this cart is 10 m.p.h.
CAUTION:
INJURY, BEFORE RELEASING THE
LATCH BE SURE THAT NO ONE IS
NEAR THE CART.
MAINTENANCE
1. At the beginning of each season, lubricate, with a light
machine oil, the latch, the latch pivot bolt, and the area
of the axle where the draw bar tongue pivots.
2. Grease or oil the wheel bearings periodically. Use
automotive wheel bearing type grease or 20 weight oil.
3. Keep tires filled to the recommended tire pressure of
printed on the tire.
CART MODEL SPECIFICATIONS
MODELS 45-01012 & 190-653B
Tires:
16.00" x 4.0" Pneumatic
Axle:
3/4" Dia. Steel
Capacity:
Up to 750 Lbs. Max.
Approx. Sh. wt.
105 Lbs.
7
IMPORTANT!
TO AVOID POSSIBLE