ADE 8EP420 Installation Instructions - Page 2
Browse online or download pdf Installation Instructions for Security System ADE 8EP420. ADE 8EP420 2 pages. Bell box
Installation
Panel
Board
J6
-
+
T A
D B
SET
STROBE
+ve
BELL
SCB
-
+
-
-
-
-
+
+
BATTERY
RTN
HOLD
TRIG
OFF
T
D
A
B
Board
Reson8
Wiring
Reson8
ADE Control
panel
STB-
STROBE -
TRIG-
B -
HOLD OFF - A -
HOLD OFF + D +
RTN-
T -
BATTERY -
Connect - from Reson8 battery
BATTERY +
Connect + from Reson8 battery
Timer
The Reson8 will operate under normal
alarm conditions as directed by the
TIMER SETTINGS
control panel. However, if the Reson8
J6
Test
is triggered into Self Activating Bell
mode (SAB), due to power loss or
J5
20 minutes
cable damage, then the sounder will
J4
10 minutes
operate from the Ni-Cad battery for the
J3
5 minutes
set time. The minimum time setting is
marked as "TEST" which will limit the
bell to 5 seconds of operation.
"
After testing, please ensure that the timer is
correctly set to the desired position. The 20 minutes
duration is typical for most installation.
Status Indicators
The two LED indicators are used to display the status of the
Reson8. The red LED illuminates to indicate the hold off supply is
present. The green LED illuminates to show the there is no
tamper, that is the tamper circuit is closed and healthy.
Novar Systems Limited reserves the right to revise this publication from time to time and make changes to the
content hereof without obligation to notify any person of such revisions of changes.
2
Panel
Board
F5
J6
1A
-
STB
Board
Reson8
Other control panel
- Strobe or -ST
Bell -
Tamper supply -
Bell +
Tamper return -
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK
Telephone +44 (0) 116 246 2000
F5
-
+
T A
D B
SET
STROBE
+ve
BELL
SCB
1A
-
+
-
-
-
-
-
+
+
BATTERY
RTN
HOLD
TRIG
STB
OFF
T
D
A
B
The LED status indicators will operate in one of
LEDs
two modes as a means of deterrent.
J2
C
A
L
O
T
N
ALT: Alternating between Red & Green LED's
LED3
LED2
or CON: Red & green LED's are constantly
illuminated.
(Red)
(Green)
Battery Enable
Reson8 is supplied with a 6 Volt internal Ni-cad
Battery
battery, as part of the Self Activating Bell (SAB)
circuit. When commissioning the system you will
On Off
need to enable the battery in order to provide
J1
battery back up in the event of mains supply
failure.
&
Note on connecting the battery link the
sounder will output tamper alarm.
Final Test
When installation is complete the Red (Hold Off Supply) LED
indicator should be illuminated. The green indicator will illuminate
when the lid is securely fixed into position.
We recommend that the following tests are then carried out:
¨
Test the operation of the sounder and the timer in
self-actuating mode, by removing the hold off supply to the
Reson8.
¨
Test the operation of the front cover tamper.
¨
Test the operation of the sounder and strobe, by generating
an alarm condition at the intruder control panel.
Registered office: Novar House: 24 Queens Road, Weybridge, Surrey KT13 9UX
Reson8
Blue
-
-
-
-
-
+
+
BATTERY
RTN
HOLD
TRIG
STB
OFF
Board
T
D
A
B
Reson8
Website: www.ade.co.uk
Fax (UK): +44 (0)116 246 2566
4188-831 issue 1_2/05_reson8