BENDIX BDW 45 Instruction Book - Page 8

Browse online or download pdf Instruction Book for Dishwasher BENDIX BDW 45. BENDIX BDW 45 16 pages. Dishwasher
Also for BENDIX BDW 45: Instruction Book (16 pages)

Print Page

Installation

Any electrical work required to install this appliance

should be carried out by a qualified electrician or

competent person.

Any plumbing work required to install this appliance

should be carried out by a qualified plumber or competent

person.

Remove all packaging before positioning the machine.

If possible, position the machine next to a water tap and a

drain.

Levelling

Good levelling is essential for correct closure and sealing of

the door. When the appliance is correctly levelled, the door will

not catch on the levelling spacers on either side of the

cabinet. If the door does not close correctly, loosen or tighten

the adjustable feet until the machine is perfectly level.

Water supply connections

This dishwasher must be plumbed into a cold water supply.

The water pressure must be within the limits given in the

"Technical specifications" (Instruction Book - Part 2).

Your local Water Authority will advise you on the average

mains pressure in your area.

The dishwasher features fill and drain hoses which can be

turned either to the left or the right to suit the installation.

Do not use, for connection, old hoses which have been

used in another appliance.

The locknut must be correctly fitted to avoid water leaks.

Avoid bends or kinks in the hose which could prevent or slow

down the water supply.

If the machine is connected to new pipes or pipes which have

not been used for a long time, you should run the water for a

few minutes before connecting the inlet hose. This will prevent

deposits of sand or rust clogging the inlet hose.

Water outlet hose connection

The end of the drain hose can be connected in the following

ways:

1. To the sink outlet spigot, securing it if necessary with a

clip.

2. Hooked over the edge of the sink using the special

curved plastic guide (if provided).

3. To a stand pipe provided with vent-hole, minimum

internal diameter 4 cm.

CS09

The waste connection must be at a height of between 30 cm

(minimum) and 100 cm (maximum) from the bottom of the

dishwasher.

The drain hose can face either to the right or left of the

dishwasher

Ensure the hose is not bent or squashed as this could prevent

or slow down the discharge of water.

If you use a drain hose extension it must be no longer than 2

metres and its internal diameter must be no smaller than the

diameter of the hose provided.

Likewise the internal diameter of the couplings used for

connections to the waste outlet must be no smaller than the

diameter of the hose provided.

The sink plug must not be in place when the machine is

draining as this could cause the water to siphon back into the

machine.

CS10

Attention!

Our appliances are supplied with a with a security device

to protect against the return of dirty water back into the

machine.

If the spigot of your sink has a "no return valve"

incorporated this can prevent the correct draining of your

dishwasher. We advise you therefore to remove it.

Electrical connection

This appliance must be earthed.

The manufacturer declines any responsibility should this

safety measure not be observed.

If the plug that is fitted to your appliance is not suitable for the

socket, it must be cut off and the appropriate plug fitted.

Important

The wires on the mains lead are coloured in accordance with

the following code:

Green and Yellow

-Earth

Blue

-Neutral

Brown

-Live

If you fit your own plug,

the colours of the wires

in the mains lead of

your appliance may not

correspond with the

markings identifying the

terminals in your plug.

Proceed as follows:

1. Connect the Green and Yellow (earth) wire to the terminal

in the plug which is marked with the letter "E" or the earth

symbol

or coloured green and yellow.

2. Connect the Blue (neutral) wire to the terminal in the plug

which is marked with the letter "N" or coloured black.

3. Connect the Brown (live) wire to the terminal in the plug

which is marked with the letter "L" or coloured red.

The plug moulded onto the lead incorporates a 13amp BSI362

fuse. Only ASTA or BSI fuses should be used.

The plug must not be used if the fuse cover/carrier is lost. The

cover/carrier is indicated by the coloured insert at the base of

the plug.

A replacement cover/carrier must be obtained from your local

Service Force Centre.

+ 2 m max

CE04