Gage Bilt GB703SRVT Installation Manual - Page 6

Browse online or download pdf Installation Manual for Power Tool Gage Bilt GB703SRVT. Gage Bilt GB703SRVT 15 pages.

DESCRIPTION

WARNING:

The balance of this tool is designed for horizontal use and is not suited for any other applications.

Gage Bilt will be pleased to advise for your specific application.

The GB703SRVT is a pneumatic-hydraulic split handle riveter designed specifically for the efficient installation of a wide range of blind rivets. This

tool's unique "split" system provides the operator with a lightweight ergonomic tool. The head assembly when held in hand weighs just 1.5 lbs

(.68kg)! The entire split handle riveter weighs 11 lbs. (4.99 kg). It has a .780" (19.81mm) rivet setting stroke.

The GB703SRVT split handle riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing maximum efficiency.

At 90 psi, (6.2 bar) the GB703SRVT does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles per minute.

The GB703SRVT comes with 3 feet of hose. Vacuum systems are available for this tool, please consult our engineering department

for specific applications.

The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting.

THE GB703SRVT IS SOLD RIVET SPECIFIC. PLEASE REFER TO PAGE 14 TO PULL ANY RIVETS OTHER THAN WHAT TOOL WAS

PURCHASED FOR.

MAINTENANCE

WARNING:

Maintenance personnel

WARNING:

Disconnect tool from its power source before performing maintenance.

WARNING:

Excessive contact with hydraulic oil and lubricants should be avoided.

WARNING:

Dispose of Hydraulic Oil in accordance with applicable regulations.

WARNING:

Read MSDS documents for all applicable materials.

The performance of any tool depends upon good maintenance practices. Following these minimal requirements for ser-

vice and care will extend the life of your tool.

*Only use an air supply set at 90-100 psi (6.2-6.9 bar) equipped with a filter-regulator to prevent wear.

*The tool will eventually lose some hydraulic oil. Keep the hydraulic system full (only use Dexron III, or equivalent)

and free of air by using the air bleeder assy (704153) on a weekly basis.

*Proper care by operator is necessary in maintaining full productivity and reducing downtime. Read all applicable

tool manuals and nose assembly data sheets prior to operating tools.

*Keep nose assemblies, especially jaws, clean and free of chips and debris. Lube jaws and collet surfaces

that jaws ride on with light machine oil

*All Screwed End Caps, Base Covers, Air Fittings, Actuators, Screws and Nose Assemblies are to be examined at the

end of each working shift to check that they are secure.

*Check tool, all hoses and all couplings daily for damage or air/hydraulic leaks. Tighten or replace (if necessary).

*For a complete overhaul, tool kit GB704TK is recommended.

HYDRAULIC THREAD PREPARATION

IMPORTANT:

Be sure to use thread sealant on all hydraulic fittings, Loctite® 30534 or similar Teflon® infused pipe

dope is recommended.

properly applied, pieces of Teflon may enter the hydraulic system and cause malfunction or damage.

Use 1 1/2 wraps of tape on each thread. Cut off all loose tape ends. Tighten until fitting feels snug and

then go 1/2 to a full turn past that point.

CLEANING AND LUBRICATING PROCEDURE

Daily cleaning and lubrication of nose assembly will greatly reduce

downtime and increase life of components. Using sewing machine

oil, or an equivalent cleaner/lubricant, follow instructions below.

1. Disconnect tool vacuum line (if equipped).

2. Point nose assembly into oil as shown.

3. Cycle tool 8-10 times and wipe dry.

TORQUE SPECIFICATIONS

Socket Head Cap Screws (400061 and 400066) = 40 inch lbs.

Button Head Cap Screws (A-928) = 40 inch lbs.

Flexlock Nut (400559) = 40 inch lbs.

Packing Plug (704118) = 45 foot lbs.

End Cap (703114) = 45 foot lbs.

Button Head Cap Screws (402482) = 35-40 inch lbs. (Do NOT over-tighten)

MUST

read and understand all warnings and cautions.

on a

daily basis.

CAUTION:

Teflon tape is an excellent thread sealer, however, if it is not

CAUTION:

Over tightening can easily distort the threads.

Image may not

reflect actual tool

9/14