Gaggenau BX 281 Installation Instructions Manual - Page 3

Browse online or download pdf Installation Instructions Manual for Oven Gaggenau BX 281. Gaggenau BX 281 16 pages.

Print Page
Für Österreich:
Im Fehlerfall kann ein Gleichstromanteil von größer als
5 mA bzw. 20% des Gesamtfehlerstromes auftreten.
Fehlerstromschutzschalter älterer Bauart müssen
durch einen Typ neuerer Bauart ausgetauscht werden.
Eckeinbau – Bild 2
Frontüberstand inklusive Türgriff für die Öffnung von
seitlichen Schubladen beachten:
Abstand Möbelwange – Türfrontfläche: 47 mm.
Abstand Möbelwange – Türgriffaussenkante: 94 mm
Bei Planung einer Ecklösung Türöffnungswinkel mind.
90° beachten.
Einbau – Bild 3
Wichtig: Gewicht des Doppelbackofens beachten
(ca. 150 kg mit Zubehör). Gerät nur aufrecht
transportieren.
Wichtig: Gerät nicht an Tür, Türgriff oder unterer
Luftleiste anheben. Gerät an den seitlichen
Montagegriffen anheben.
Gerät in das Einbaumöbel einschieben. Gerät mittig
und waagrecht ausrichten.
Zwischen Gerät und angrenzenden Möbelfronten einen
Spalt von mindestens 5 mm belassen.
Gerät mit beiliegenden Schrauben befestigen.
Kombination mit Wärmeschublade
WS 2..
Wichtig: Gewicht des Doppelbackofens beachten
(ca. 150 kg mit Zubehör). Über der
Wärmeschublade muss ein ausreichend stabiler
Zwischenboden montiert werden.
en
$

Important Notes

The appliance is only guaranteed safe to use if installed
by a specialist in accordance with these installation
instructions. Shock protection must be guaranteed by
the installation.
The installer is liable for any damage resulting from
incorrect installation.
The appliance may only be connected by a licensed
specialist. The local electricity supplier's regulations
and construction regulations apply.
Check the appliance for any transport damage.
The appliance must be disconnected from the
electricity before any installation work takes place.
Preparing the Cabinet – Figure 1
Important: Pay attention to the weight of the
double oven (approx. 150 kg with accessories).
The support floor of the cabinet must be able to
withstand this weight.
Fitted units must be heat-resistant up to 90 °C,
adjacent unit fronts up to at least 70 °C.
Cut out the units before fitting the hob. Remove
shavings as they can affect the function of electrical
components.
Secure furniture which is not fitted to the wall using a
standard fixture.
Install the appliance low enough to allow baking trays
to be easily removed.

Electrical Connection

Observe rating plate data for voltage and total rating.
Important: Only connect in accordance with the
connection diagram. Fit the enclosed copper bridges
as required.
Mains connection lead: Type H05 VV-F or higher. The
yellow-green lead for the earth connection must be 10
mm longer on the appliance side than the other leads.
The rear of oven has tapered edges. When cabinet
depth is 550 mm, the connection lead must be guided
down the rear right side of the cabinet to the connector
box. Position connector box beneath the cabinet
recess.
Do not trap the connection lead during installation and
do not guide it over sharp edges.
The appliance corresponds to safety class I and may
only be used in conjunction with a safety earth terminal.
Fuse protection using B or C circuit breakers is
required.
An all pin isolating switch with a contact gap of at least
3 mm must be installed.
Corner installation – Figure 2
Observe space requirements of door and door handle
when planning drawers beside the appliance:
measurement cabinet edge – door panel: 47 mm.
measurement cabinet edge – door handle edge: 94 mm
Observe a minimum opening angle of 90° for corner
installation.
Installation – Figure 3
Important: Pay attention to the weight of the
double oven (approx. 150 kg with accessories).
Transport the appliance in an upright position.
Important: Do not lift the appliance by the door, door
handle or lower air vent. Lift the appliance by the
installation handles on both sides.
Insert the appliance in the cabinet and align it centrally
and horizontally.
3