Dynabrade 10472 Model T Operating, Maintenance And Safety Instructions - Page 2
Browse online or download pdf Operating, Maintenance And Safety Instructions for Sander Dynabrade 10472 Model T. Dynabrade 10472 Model T 4 pages. Dynabug “model t” sander operating, maintenance and safety instructions
Print Page
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: Turbine air motor, no oil required.
Operating Instructions:
Warning: Eye, face, sound, respiratory and body protection must be worn while operating power tools. Failure to do so may result in serious
injury or death. Follow safety procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting
to avoid damaging valve body housing.
3. Connect power source to tool. Be careful not to depress throttle lever in the process.
Maintenance Instructions:
1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be
serviced to correct the cause before use.
2. Some silencers on air tools may clog with use. Clean and replace as required.
3. An Air Line Filter-Regulator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11402 Air
Line Filter-Regulator – Provides accurate air pressure regulation, two-stage filtration of water contaminants.
Operates 40 SCFM @ 100 PSIG and has 3/8" NPT female ports.
4. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM
of your machine.
5. A Motor Tune-Up Kit (P/N 96169) is available which includes assorted parts to help maintain motor in peek operating condition.
Please refer to Dynabrade's Preventative Maintenance Schedule for a guide to expectant life of component parts.
6. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids,
esters, keytones, chlorinated hydrocarbons or nitro carbons.
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
•
Important: User of tool is responsible for following accepted safety codes such as those published by the American National
Standards Institute (ANSI).
•
Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
•
Inspect abrasives/accessories for damage or defects prior to installation on tools.
•
Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality
pneumatic motors can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water
contained in the air supply into motor bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited
efficiency and power. Our warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been
subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one
year from the date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal
use and service. We shall repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the
original purchaser, indicate upon our examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools
in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been subject to
misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as bearings,
contact wheels, rotor blades, etc., are not covered under this warranty.
®
Abrasive Power Tool.
Notice
One Year Warranty
(PD03•11)
2