Dynabrade 18066 Safety, Operation And Maintenance - Page 4

Browse online or download pdf Safety, Operation And Maintenance for Sander Dynabrade 18066. Dynabrade 18066 4 pages. Long board sander. dual piston.

Print Page

Important: To keep tool safe a Preventative Maintenance Program is recommended whenever portable power tools are used.

• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and SPM of your air tool.

• It is strongly recommended that all Dynabrade air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due to unclean

air, wet air or insufficient lubrication. Dynabrade recommends the following: 10681 Air Filter-Regulator-Lubricator (FRL) – Provides accurate air pressure

regulation and two stage filtration of water contaminates.

• Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the

filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.

Routine Preventative Maintenance: Check free speed of Long Board Sander regularly using a strobe tachometer without abrasive accessory attached with

90 PSIG at inlet while tool is running. Always check tool speed after any maintenance or repair. If tool is operating at a higher SPM (speed) than marked on

the housing, or operating improperly, the tool must be corrected before use.

• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, ketones,

chlorinated hydrocarbons or nitro carbons.

• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40

• Air tool stampings must be kept legible at all times, if not, reorder and replace. User is responsible for maintaining specification information.

i.e.: Model #, S/N, and SPM.

• Blow air supply hose out prior to initial use.

• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.

• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.

After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.

Check for excessive tool vibration.

Handling and Storage:

• Protect tool inlet from debris.

• DO NOT carry tool by air hose.

• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.

• Store accessories in protective racks or compartments to prevent damage.

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within 6 months

from the of date purchase, "Autobrade Red" tools are warranted against defects in workmanship and materials under normal use and service.

We shall, at our option, repair or replace at our factory, any "Autobrade Red" tool which shall, within 6 months

after delivery to the original purchaser, indicate upon our examination to have been defective.

Our obligation is contingent upon proper use of "Autobrade Red" tools in accordance with factory recommendations, instructions and practices.

The warranty shall not apply in these cases:

1. Normally wearable parts such as bearings, rotor blades, etc.

2. Consumables such as sanding pads, etc.

3. Misuse, neglect in maintaining tool or tool modification.

4. Lack of lubrication or evidence of rust, dirt or corrosion.

Reference Contact Information

1. American National Standards Institute – ANSI

25 West 43

Street

Forth Floor

New York, NY 10036

Tel: 1 (212) 642-4900

Fax: 1 (212) 398-0023

Visit Our Web Site: www.dynabradeauto.com

DYNABRADE Automotive Aftermarket 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073

Maintenance Instructions

Autobrade Red Tool Warranty

5. Tools requiring normal tune-up or cleaning.

6. Tools being used after they are badly worn such as using ratchet with worn yoke.

7. Ratchets, anvils damaged by excessive hand torquing.

8. Use in production-type applications.

Products to be considered for warranty must be sent back

to our factory, transportation prepaid by the user. Please

send tool back to attention of "Repair Department" with

note fully explaining the nature of the problem along with a

copy of original invoice indicating model and serial number.

2. Government Printing Office – GPO

Superintendent of Documents

Attn. New Orders

P.O. Box 371954

Pittsburgh, PA 15250-7954

Tel: 1 (202) 512-1803

PRINTED IN USA

Return product to:

Dynabrade, Inc.

Attn: Repair Department

8989 Sheridan Dr.

Clarence, NY 14031

3. European Committee for Standardization

Rue de Stassart 36

B - 1050 Brussels, Belgium

DYNABRADE

APD09.01