ADELSYSTEM CBI6024A Instruction Manual - Page 3

Browse online or download pdf Instruction Manual for UPS ADELSYSTEM CBI6024A. ADELSYSTEM CBI6024A 5 pages. Dc ups

Print Page

Battery Temperature Compensation Charge

Connecting the cable RJTEMP (supplied separately) to Auxiliary Output

AUX1, the CBI will adjust the battery charging voltage in relation to the

Battery temperature:

Fast Charge: Open Lead, AGM, Gel

+/- 5mV/°C x n. of Cells from -8°C to +60°C

+140 ÷ -200 mV/Cell compared to the value at

20°C

Fast Charge: Ni-Cd

+/- 2.5 mV/°C x n. of Cells from -20°C to +60°C

+100 ÷ -100 mV/Cell compared to the value at

20°C

The device stops charging the battery if the temperature is below -20°C

or above +60°C. The sensor placed on cable RJTEMP must be applied

on the battery.

Device Configurations

Completely automatic, all devices are suitable to charge most batteries

types thank to User Selectable charging curves. They can charge open

lead acid, sealed lead acid, Gel, Ni-Cd and Li-Ion. It is possible to change

or add other charging curves connecting the web server device to a PC.

Configurations

Note: it is also possible to configure the device via Web server

In normal operation the LED bargraph (No.19 in sect.7) gives an

indication of the current (0 to 100% of In) as follows:

•

In charge mode with mains:

battery charge current with solid light

•

In backup mode without mains: battery discharge current with

blinking light

•

In boost mode with mains: battery discharge current with

flickering light

To display the current device configuration on the LED bargraph press

the Config/Start button (No.9 in sect.7) briefly (< 1 sec). The display

returns to normal operation after 10 seconds. Please refer to the pictures

at the end of this section.

To change the device configuration, complete the procedure below (note:

if the procedure is not completed no settings are saved; the procedure is

aborted if no command is given for 60s).

With battery disconnected:

•

press the Config/Start button (No.9 in sect.7) for more than 2

seconds, until the first led starts blinking

•

press briefly the button to cycle through the battery types as

shown by LEDs 1,2,3 (please refer to the pictures at the end of

this section) then confirm with a long press until the 4th LED starts

blinking

•

LED 4: Config Mode: ON/OFF

•

Long press to enable a complete configuration via Web Server,

Modbus/SNMP and APY351/ADELViewSystem (Led ON).

•

Short press to configure basic parameters from the device front

panel or from the web server System page (Led OFF)

•

If Config Mode was selected, the procedure terminates here

•

LED 5: Option: not used: continue with a short-press

•

LED 6: Life Test; long press to enable the function (Led ON), short

press to disable

•

LED 7: Fast Charge; long press to enable the function (Led ON),

short press to disable

•

LED 8: UPS Disable; long press to disable the UPS function (Led

ON), short press to keep it enabled

•

LED 9: Buffering time: press briefly the button to select the max

backup duration, then confirm with a long press. The current

selection is shown with other LEDs blinking together with LED 9

as follows:

•

Led 1: 30 sec; Led 2: 120 sec; Led 3: 300 sec; Led 4: 10 min; Led

5: 15 min; Led 6: 20 min; Led 7: 30 min; Led 8: 45 min; All leds:

Infinite time

•

Note: the last selection (infinite time) is confirmed automatically

also with a short press

•

More values can be selected by Web Server, Modbus, SNMP and

with DPY351 or ADELVIEWSystem

•

End Programming: the device shows the selected configuration

for 10 seconds then resumes normal operation,

With battery connected:

•

press the Config/Start button (No.9 in sect.7) for more than 2

seconds, until the 5th led starts blinking

•

follow the procedure above from step "LED 5: Option" (Battery

Type and Config Mode can be changed only when the battery is

not connected).

Float charge: Open Lead, AGM, Gel

+/- 3mV/°C x n. of Cells from -20°C to +60°C

+120 ÷ -120 mV/Cell compared to the value at 20°C

Float charge: Ni-Cd

+/- 2.5 mV/°C x n. of Cells from -20°C to +60°C

+100 ÷ -100 mV/Cell compared to the value at 20°C

Via Luigi Barchi 9/B – Reggio Emilia 42124 – Italy

Tel. +39 0522 345518 – Fax +39 0522 345551 –

Battery Type chemistry Selection

LED Config

(Size 5)

Open Lead

(AGM) Low

Gel Battery

Ni-Cd

Li-Ion (4)

LiFePo4

Config Mode (5)

Functional Setting

Battery Life

test ON

Fast Charge

Enable (3)

UPS Disabling

Time Buffering

"Start from

Battery" (No

Input Mains)

Data and Communication

ADELBus connection

Remote device connection by terminals 22. This device features the

ADELBus communication protocol for the connection of other devices on

CAN bus, for monitoring, configuring, driving and updating them(fig.3).

www.adelsystem.com

Instruction Manual CBI60_4

Float charge

Fast charge

(Volt/Cell)

2.23

2.40

2.25

2.40

2.30

2.40

1.4V/cell

1.45V/cell

(12V:10 cells)

(24V:20 cells)

(48V:40 cells)

3.45V/cell

3.65V/cell

12Vfield: 13.8V

12Vfield: 14.6V

24Vfield: 27.6V

24Vfield: 29.2V

48Vfield: 55.2V

48Vfield: 58.4V

Configure with ADELViewSystem or Web

Server for CBI60

Life test enabled

Fast Charge enabled.

UPS function enabling. Use terminal 12 for

connection to external Contact.

1 blink => 0.5, 2 blink => 1,

3 blink => 5, 4 blink => 10,

5 blink => 15, 6 blink => 20,

7 blink => 30, 8 blink => 45 min

9 Solid =>

infinite"

∞

(Time = minute)

System switch ON from battery without

mains. For connection to external Push

button use terminal 12

Page 3