HiB 48400 Manual

Browse online or download pdf Manual for Indoor Furnishing HiB 48400. HiB 48400 2 pages. Bluetooth cabinets
Also for HiB 48400: Assembly Instructions (4 pages)

Print Page

This product is suitable for installation in zones:

Outside Zone

All installations must comply with guidelines which are based on a zonal

concept. The diagram above illustrates this concept and must be followed

to ensure the safe installation of electrical appliances in the bathroom.

These regulations apply to domestic installations only. Installations must be

made in accordance with the current IEE wiring regulations and relevant

building regulations. HiB recommends that all electrical bathroom

products should only be fitted by a suitably qualified, Part P registered

electrician.

Installation

Before installation, ensure the domestic electrical mains supply to

which the cabinet is to be connected is turned off. Before drilling,

ensure that there are no hidden cables or pipes in the wall.

recommended that the fitting of this product is conducted by two people.

1. Before commencing installation, remove the door(s) from the carcass. This

is done by gently pulling at the tab at the back of each hinge, as

A. Carefully move the door away from the cabinet while gently extracting

the wire. Disconnect the cable connector and place the cabinet door(s)

carefully onto a soft surface where they will not get damaged during

installation.

2. Position the cabinet in a suitable location (according to the zonal diagram

(Fig. 1) above) ensuring that the mains supply cable is within reach of the

cable connection point of the cabinet. Carefully mark the desired position

of the cabinet using a soft pencil, ensuring it is level.

3. Remove the cabinet from the wall and using a spirit level, mark a horizontal

line below the pencil mark, taking into account the location of the

mounting points (Fig. B). Place brackets on the line paying attention to the

distance between the hangers on the cabinet. Carefully mark the position

Door Removal (Fig. A)

+44 (0)20 8441 0352

+44 (0)20 8441 0219

Building 3, North London Business Park, Oakleigh Road South, New Southgate, London. N11 1GN

©HiB Copyright: No part of this document may be reprinted or duplicated without HiB consent. All sizes and measurements are approximate, but we do try and make sure they are as accurate as possible. In the

interest of continuous product development, HiB reserves the right to alter specifications as necessary. E & OE.

(Fig. 1)

It is strongly

per Fig.

REAR VIEW

Mounting Points

Location of internal

xing hole (SINGLE DOOR)

Location of internal

xing hole (DOUBLE DOOR)

Fixing Brackets (Fig. B)

[email protected]

Thank you for purchasing this HiB product.

Please read through these instructions carefully and refer back to them

during installation to ensure that your product is fitted safely and that it

retains its high quality finish.

Please retain this leaflet for future reference.

of the holes using a soft pencil. (Fig. C).

4. Before drilling, ensure there are no hidden cables or pipes behind the

mounting point. Using a suitable drill bit, drill holes in the marked positions

to a suitable depth.

5. Insert wall plugs level with the surface of the wall. If fitting to a tiled surface,

wall plugs should be inserted below the tile surface to avoid cracking. NB.

For plasterboard walls, specialist fixings should be purchased from any DIY

or hardware store.

6. Fix the brackets to the wall using the screws provided.

7. Carefully remove the small screws along the top front edge of the cabinet

to gain access to the internal panel(s) (Fig. D) Keep screws in a safe place.

8. Temporarily hang the cabinet ensuring the claws on the hangers are

securely located on the wall brackets. Using a spirit level adjust the cabinet

via the screws on the hangers (Fig. D).

9. Mark the position of the internal fixing hole and remove the cabinet. Using

a suitable drill bit, drill a hole and insert a wall plug as per stage 4.

10. Connect the cable at the rear of the cabinet to the mains supply cable using

a suitable terminal block (not supplied) according to the wiring diagram

(Fig. 2) on the back page.

11. Rehang the cabinet in position, tighten the screws on the hangers (Fig. D)

and secure the base of the cabinet with the supplied screw(s) and screw

cap(s).

12. Insert the supplied shelf brackets into the appropriate holes on the inside

of the cabinet, depending on what height each shelf is required. Slide each

shelf into position and secure in place by tightening the small plastic grub

screw on the underside of each shelf bracket.

13. With help from a second person,

carefully connect the cable connector - take care to connect the wires in

the correct orientation. Once connected, carefully slide any excess wiring

and the connectors inside the carcass and reconnect the hinges. Hinges

are reconnected by clipping the front of the hinge in and then applying

pressure on the back of the hinge until an audible 'click' is heard.

14. Switch the mains supply back on.

Hanging Brackets (Fig. C)

hib.co.uk

FI#02 014 R170405

Groove Cabinets

Groove 50

Art No. 48400

Groove 60

Art No. 48500

Groove 80

Art No. 48600

offer the door up to the cabinet and

Angle Adjustment

Claw In/Out

Adjustment

Hanger Adjustment (Fig. D)

Ver No.

1.0 Jan 2017