Automate 7645A User Manual - Page 2

Browse online or download pdf User Manual for Remote Control Automate 7645A. Automate 7645A 4 pages. Dealer master remote control

1.
Press and hold the
AUX
AUX
LED comes on solid (after approximately 10 seconds).
AUX
Note: The LED flashes once per second while the buttons are
depressed.
2.
Release the buttons – the LED turns off.
3.
Press/release the corresponding remote control button for the
desired RF range as listed below. The LED flashes in groups to
confirm the range setting.
selects the shortest range, the LED flashes once.
selects the short intermediate range, the LED flashes twice.
AUX
AUX
selects the long intermediate range, the LED flashes three
AUX
AUX
times (as the default setting, no initial selection is required).
AUX
AUX
selects the longest range, the LED flashes four times.
4.
Once the number is entered, wait for 20 seconds for the re-
mote to exit the routine.
Note: The LED flashes four times confirming the routine is ex-
ited.

Battery Information

The remote controls are powered by 1 coin cell battery (CR-2032)
that can be purchased at most retailers. When the battery begins
to weaken, the operating range will be reduced.
Battery Replacement
1.
Unscrew the hardware (if used) on unit rear and remove from
housing.
2.
Hold the unit base with one hand and gently twist and pull the
main housing body with the other. This releases all parts of the
housing assembly.
3.
Remove battery from clip and replace with a new one while
observing the correct polarity.
4.
Reassemble unit and secure with hardware.
Battery Disposal
Directed cares about the environment. If you need to
dispose of the battery, please do so in accordance with
your municipal requirements for battery disposal.
2
&
button simultaneously until the
AUX
FCC/ID Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Any changes or modifications not expressly approved by the party responsi-
ble for compliance could void the user's authority to operate the equipment.
Canada statements:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouil-
lage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélec-
trique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement..
© 2012 Directed. All rights reserved.
G7645A BL 2012-05