Great World GW-6078TBT Operating Manual - Page 5
Browse online or download pdf Operating Manual for Electric Heater Great World GW-6078TBT. Great World GW-6078TBT 7 pages.
Print Page
INSTALLATION
Reminders
1. The dimension of the electric fireplace insert is 23.38" wide (59.2cm) x
20.63" high(52.4cm) x 5.31" deep(13.5cm). You may want to leave a
clearance around the insert of 1/4"(0.6cm) for easy installation.
2.Place the electric fireplace insert in the desire location or build a wall
construction in the desire location. The ideal size of space for inserting
should be 22.13"(W) x 20.28"(H) x 13"(D).
3. The electrical outlet must be 15A/120V. Make certain that the outlet is
near the location where electric fireplace insert is installed so that the
use of an extension cord is not necessary. If extension cord must be
used, make sure the cord is UL approved and allow 15A/120V power.
4. Avoid installing the electric fireplace insert in areas such as bathrooms,
kitchen, or laundry rooms where excessive moisture or water may be
present. DO NOT place heater on carpet, near drapes or materials that
may easily catch fire.
5.Make sure the four rubber feet are attached to the bottom of the electric
fireplace insert. Removing them will hinder air circulation under the unit.
6.Minimum installation external dimension: 555mm*513mm*180mm.
7.Minimum installation internal dimension: 595mm*527mm*180mm.
Specification
Insert the electric fireplace insert into the wooden fireplace cabinet/mantel
from the back. The electric fireplace insert should be attached to the
cabinet/mantel with the screws included in the hardware kit using a
screwdriver (not provided) as shown in the figure below.
NOTE : Wooden fireplace cabinet exterior is only for reference. Install the
device into the product you purchased.
"Grounding Instructions :
This fireplace is for use on 120V outlets. The cord has a 3-prong plug (See
Figure A). An adapter is available for connecting 3-prong grounded-type
plug to two-slot receptacles ( See Figure C). The green grounding plug
extending from the adapter must be connected to a permanent ground
such as a properly grounded outlet box. The adapter should not be used if
a three-slot grounded receptacle is not available.
Wooden Fireplace Cabinet
Metal Screw
Cover of Grounded
Outlet Box
Grounding Pin
(A)
MAINTENANCE
Reminders
1. Following the "IMPORTANT OPERATING INSTRUCTIONS" and
"OPERATION DETAILS" as well as periodic checks and maintenance
are necessary to extend the life of this electric fireplace insert.
2. To avoid the risk of electrical shock, ALWAYS disconnect the power cord
from the electrical outlet before any internal maintenance or replacement
of parts in done.
3. DO NOT tighten power cord with cords of other appliances when in use.
4. Use caution when opening the metal cabinet of the electric fireplace
insert during inspection and maintenance. If you need replacement parts
or have questions regarding the use or maintenance of this electric
fireplace insert lease contact our customer service number at
1-888-878-8820.
5. Make sure plug is fully inserted into the electrical outlet to avoid fire
caused by short circuit.
NOT
FULLY
PLUG IN!
OUTLET
Specification
1. There are two strips of LED lights in the base of this electric fireplace
insert. LED lights are designed for energy efficiency as well as long life
and will rarely need to be replaced. However, should you notice a dark
section of the flame or logs, it may be necessary to replace one of the
LED bulbs.
2. LED lights generate much less heat when they are on. However, allow
at least 15 seconds for LED lights to cool off before touching the LED
light bulb surface to avoid burning of skin.
3. There are two(2) strips of LED lights used in this electric fireplace insert.
ADAPTER
Ground Means
Grounding Pin
(B)
(C)
(D)
FULLY
PLUG IN!
OUTLET