Automatic Solutions KING 24V User Manual - Page 3

Browse online or download pdf User Manual for Gate Opener Automatic Solutions KING 24V. Automatic Solutions KING 24V 14 pages. Con / avec / with / mit t2 24v leaf gates

Print Page

INSTALLATION KING 24V

RE-INSTALLATION CHECKS

The leaf must be fixed firmily on the hinges to the pillars, must not be

flexible during the movement and must move without frictions.

Before the installation of KING 24V, verify all dimensions etc.

There's no need for any modification, if the gate is like that shown

in Fig. 1.

Gate features must be uniformed with the standards and laws in

force. The gate can be automated only if it is in a good condition and

its conditions comply with the EN 12604 norm.

- The gate leaf does not have to have a pedestrian opening. In the

opposite case it is necessary to take the appropriate steps, in

accordance with EN 12453 norm (for instance; by preventing the

operation of the motor when the pedestrian opening is opened, by

installing a safety microswitch connected with the control panel).

- No mechanical stop shall be on top of the gate, since mechanical

stops are not safe enough.

IXING THE ACTUATOR ATTACHMENT TO THE COLUMN

To obtain a correct movement of the leaf gate it is necessary to respect

the measures (to see the TABLES of the measures).

OLUMN ATTACHMENT FOR KING 24V OPERATOR

(code CCA1293 - CCA1294)

If the column is in iron, the attack can be screwed directly using four

metric screws M8.

If the column is in concrete, the attack can be fixed with four expansion

screws Ø 8 mm (Fig. 3).

In the case you have a wall parallel with the open gate, you must

provide a niche in which to place the operator.

OLUMN ATTACHMENT FOR KING 24V L OPERATOR

(code CCA1370 - CCA1319)

To obtain a correct movement of the leaf gate it is necessary to respect

the measures.

If there is an iron pillar you can weld the attachment directly.

If there is a cement pillar, you can use the fixing plate as in Fig. 5 which

is fastened with 4 Fischer-screws of Ø 8 mm.

There is also the possibility to cement the attachment welding an

anchor at its base Fig. 6.

Naturally you have to respect predetermined fixing measures.

Afterwards you must weld the other actuator's attachment to the gate

(Fig. 8).

In the case you have a wall parallel with the open gate, you must

provide a niche in which to place the operator.

IXING THE OPERATOR ATTACHMENT TO THE GATE

(to see the TABLES of the measures).

Before inserting the pin into the gate attachment, grease

thoroughly.

Weld the base at the right height (Fig. 8).

Fix the KING 24V and try several times to open and to close the gate,

controlling that the operator does not touch the moving gate.

Parts to install meeting the EN 12453 standard

COMMAND TYPE

(out of public area*)

with manned operation

with visible impulses

(e.g. sensor)

with not visible impulses

(e.g. remote controldevice)

automatic

* a typical example are those shutters which do not have access to any public way

A: C ommand button with manned operation (that is, operating as long as activated),

like code ACG2013

B: Key selector with manned operation, like code ACG1010

C: Adjustable power of the motor

D: S afety edges, like code ACG3010 and/or other safety devices to keep thrust force

within the limits of EN12453 regulation - Appendix A.

E: P hotocells, like code ACG8026 (To apply every 60÷70cm for all the height of the

column of the gate up to a maximum of 2,5m - EN 12445 point 7.3.2.1)

USE OF THE SHUTTER

Skilled persons

(public area)

C or E

C and D, or E

Unrestricted use

non possibile

C and D, or E