Dynakit MArk IV Instructions For Assembling - Page 5

Browse online or download pdf Instructions For Assembling for Amplifier Dynakit MArk IV. Dynakit MArk IV 16 pages.
Also for Dynakit MArk IV: Instructions For Assembling (12 pages)

11
12
13
14
15
16
17
18
19
20
21
22
23
(S). Connect the blue lead to pin #3 of
V3 (S). Connect the green lead to pin
#4 of V3.
Connect one end of a
10,000 ohm
(brown-black-orange) resistor to lug #5
of the five lug strip. Connect the other
end to lug #1 of the 10,000 ohm bias po-
tentiometer (S).
Connect the positive
(+)
end of the
selenium rectifier to lug #4 of the five
lug strip (S). Connect the negative (-)
end to lug #5 of the strip.
Connect the negative (-) end of a 50
mfd bias capacitor to lug #5 of the five
lug strip (S). Connect the positive
(+)
end to lug #3 of the strip.
Connect the positive
(+)
end of the
other 50 mfd bias capacitor to lug #3 of
the five lug strip. Connect the other end
to lug #2 of the 10,000 ohm bias poten-
tiometer.
Connect one end of a short piece of wire
to lug #2 of the five lug strip (S). Con-
nect the other end
to lug #3 of the strip.
If the amplifier is to be used with a Dy-
nakit PAM-1 (monophonic) preampli-
fier, this wire should be' omitted and lug
#2 soldered.
Connect one end of a
10,000 ohm
(brown-black-orange) resistor to lug #3
of the five lug strip
(S).
Connect the
other end
to
lug #1 of the strip.
Connect one end of a 4%" wire to lug
#1 of the five lug strip (S). Connect the
other end
to
lug #3 of the bias control
potentiometer (S).
Connect one end of a 2
1
h"
wire to a
mounting lug (ground lug) of the filter
capacitor (S). Connect the other end to
solder lug at mounting screw of the five
lug strip.
8trip
Ih"
of insulation from each end of
a 5" wire.
Feed one end through pin
#8 of socket V2 (8) and connect to pin
#1
(S).
Feed the other end through pin
#8 of socket V3 and connect to pin #I.
Connect one end of a 2" wire to pin # 1
of V3 (S). Connect the other end to pin
#8 of power takeoff socket (on front side
of chassis) (8).
Connect one end of the 13.5 ohm resistor
to pin #8 of V3 (8). Connect the other
end to ground lug of socket V3 (8).
SEE PICTORIAL.
Connect one end of a 3" wire to pin #8
of socket VI (8). Connect the other end
to lug #1 of the quad filter capacitor
(8) .
Connect one end of a 4" wire to lug #1
of the four screw terminal strip (8) .
24
25
26
27
28
29
30
31
(!>
(v)
Connect the other end
to
ground lug at
the five lug strip (S).
Twist together a pair of 5" wires and
connect one end of one to pin #2 of V2.
Connect the corresponding end of the
other
to pin #7 of V2. Connect one of
the other ends to pin #2 of V3, and con-
nect the last one to pin #7 of V3.
Twist together a 5
1
h"
and a 4%" wire
so that one pair of ends are uneven.
Connect the even pair of ends to pins #1
(S) and #2 (S) of the power takeoff
socket. Connect the long end to pin #2
of V3 (S). Connect the remaining end
to pin #7 of V3 (S).
Connect one end of a 10 ohm (brown-
black-black) resistor to pin #3 of the
power takeoff socket
(8).
Connect the
other end to ground lug at that socket
(S) .
Connect one end of a 22,000 ohm resistor
( red-red-orange) to pin #5 of the power
takeoff socket (S). Connect the other
end to pin #4.
Connect one end of a 5%" wire to pin
#4 of the power takeoff socket
(8).
Con-
nect the other end to filter capacitor lug
#4. (See application notes if other than
DYNA preamp is to be used.) .
Mount the printed circuit board in the
cutout at the end of the chassis. Note
that the socket is located nearest the end
of the chassis. The board should be
mounted from the bottom of the chassis
with #4 screws, nuts, and lockwashers.
The eyelets on the printed circuit board
already have solder in them. Each eyelet
has a number which will be referred to in
the instructions. Before making a connec-
tion to the board, "tin" the stripped wire
to
be connected by heating with the sol-
dering iron and touching solder to it. To
solder to the eyelet, heat the eyelet with
the iron, insert the wire when the solder
in the eyelet flows, remove the iron and
allow a few seconds for the solder to set. .
Although the metal eyelet does protect
the printed wiring from overheating, a
small iron should be used to avoid exces-
sive heat on the printed circuit board.
Connect one end of a 2" wire to eyelet #1
of the circuit board (S). Connect the
other end to the ground (short) lug of
the inpu t socket (S).
Connect one end of a 2" wire to input
socket long lug (S). Connect the other
end
to
eyelet #2
(8).
Twist together a pair of 6" wires. Con-
nect one end to pin #2 of V2 (S). Con-
nect the other end to pin #7 (S). Connect
one of the other ends to eyelet #4 (S).
Connect the remaining end to eyelet #5
(8) .
3