ADEMCO 5808C Installation Instructions - Page 3

Browse online or download pdf Installation Instructions for Security Sensors ADEMCO 5808C. ADEMCO 5808C 4 pages. Photoelectronic smoke/heat detector with built-in wireless transmitter

Print Page

4. Test the detectw immediately after mmpleting the installaflon (as

de&bed

in the TESTING s&ion of the mawa

and rsfe, to the

CIED cantml system' s iwwaons

for addtiiti

informatii

con-

' aming the use o' wl,el*ss smoke detecto,s.

Fiiun

Detector Mounting Bracket

Flgum 4. Mount Datsotw Acmss Ceiling PansI Support

W NOT sttach th* dBtecfc+ to mmovBM* oeiling panels. Attach ths

detector -

panel support as shown in Figun 4.

Thisdetectahasabui~-intsm~rswitehthatwiflcau~aCHECKrignal

to ba displayed at the oonsd* of the detactw if it Is remwed fmm ib

installation b&et.

Tfw mounting bmcketcanalwbemadetaparpmof

by breaking oft tha sm*lfw t*b *t the sodbad line (sar Figure 3). thus

p+e" entlng removal of the detector without a tool. To nmovr, the

deteotor, we *small somwddve, to depmss the tampe-f

tab and

turn the dstecfw count*rdockWse.

IEsnnG

NOTE:

Sefom testing. notify the pmpe, authwiffes that the smoke

detector *yst*m is undergoing maintenance and will tempo-

mdlybswtofsewios.

~bletheroneorsyttemunderpoing

maintenanou to pfwsnt unwanted af*mw.

Dstectom mu81 be tested after installation and following periodic main-

t*" ance. The 5303X? may be tssted ss follows:

A. TEST SWITCH

1. A massed test switch is located on the &t&o,

housing.

2. Push and hold the recessed t*st switch with * 0.t' maximum

diameter tool (en *Ilen wrench o, small scmwddw,.)

3. The LED on ths detsoto, should blink once per second.

8. TEST MODULE

(Mod., No. IOMOMI)

The MOD400R test " w&l*

can bs used with * DMM w analog

vokmstsr to check the det*ctor wnsiffvii

*I dssodbed in th* t*st

module' s manuaf.

C. SMOKE ENTRY TEST

HOld*smddedngpunkstickorcononmck*tthssideofth*d*t*ctw

and gently blow smoke thmugh th* detector until the unit *lan' ns.

D. DtRECT HEAT METHOD (Hair d,ye, o' ,ooO,Ma

watts)

Direct the heat toward

either

side thermistor. Se sum to Md the heat

sowa

about 12 inches fmm th* detector to avoid damage to th*

plastic. The detectOr will ms*t only affer it h*s time to cod.

SmOkedetsctiontestingisrscomm*ndsdfo,v*rifyingryrt*mpmtsction

capability.

A detector that fails to actfiat* wkh any of thesa tests should first be

cleaned as outlined in this manual' s MAINTENANCE section. If the

detector still fails to activate. return lo, reqai,.

Notii th% pmper

autlwitiB8

that the system is back on line.

NOTE: Remove bat&v tab before installatii

This test should be f&cm&

before installation to detsnnlns * stmng

communioatiwl path with th* QED mntml panel *nd afts, instalfation is

mmpfste. Also. ths own(N/us.w should test tha unit *t least weakly.

1. A&vat* th* ti,&ss

syst*m' * TEST mode fmm the mnsd*.

2. DqmssandMdfhesndadstedo#sTESTsvritda-,dthed&cfo,

should immsdatefy fwsmii M alarm s+M to tfw QED canw panel.

3. Thn Me&s

system' s co~oI* should *ml *t least 3 au&*

sounds

whanthsafan

transmission ismwfwdandwilldspf*yth.at,ansmft-

ting &act&

ID number.

4. Wtmn th* consde has mceived the teat slg~l. mlwse th TEST

switch. A few seconds late, the detactot? ID numb,

will cl*a, fm,,,

the consdo diifay.

5. If the cwwole does not wfxrd

as noted. cha& the polarity of the

battedes and b sun they *,a fmsh. If thfs is M fdtiil fnstaflian, try

movirq th detector to anothw lawtin

that ptidss

paps, mcep.

Lion. Also be sun that th detect&s ID h.w been ' *wolfed

by ths

QED cantid panel (sac PROGRAMMING). Then. mpa, th t*st.

6. Turn off ti* syst*m' s TEST m&

horn th cow&

(sewfty coda +

OFF).

NOTE:

Bsiom removing tk

dntactor. noMy the pmper sutfwftlea

that th* *mob

&t&a

ryrtsm is underpoi~ malnt*nanca

and will bs out of sewtce. Disabf* the z.ow o,syst*m under-

going maintensnu, to pnv*nt unw*nt*d *fans.

1. Remowths detedo,mwrbypfadngasm*ff-bladed

wmwddvain

the co%,*, rnrnowl Mot and twisting it sffght1y until the wve, can be

turned cmmt*&xkwiw

for mmovaf.

2. R*mow the -

by pulling it stmight out (sea Figun 3). V*cuum

th* rue*" thomughiy.

3. Clean the black vaned chamber p&x by vacuuming Q blowing out

dust and particles.

4. Torsinstllll~*scnen,rotetsth*~~nw,Mehouainguntilitc*ops

into ths alignment slots. CareMy push the ween onto the b&w.

making sum 1 fit* tightly to ths chamber. Rqalamm*nt scmom *m

available (c&e, part number RS23).

5. Replace the co" *, by rotating it ckxkwlrs until ft lode in place.

6. Reinstdl th* detector

into

the system, en&f*

SptSm operation. and

notify th* proper *uthmities that tfw systsm is bti

on line.

AD400-22-M

1561253-01