HID RP10MA Installation Manual

Browse online or download pdf Installation Manual for Card Reader HID RP10MA. HID RP10MA 2 pages. 13.56 mhz contactless.
Also for HID RP10MA: Installation Manual (9 pages), Installation Manual (2 pages), Installation Manual (14 pages)

Print Page

INSTALLATION GUIDE

iCLASS SE® / multiCLASS SE®

13.56 MHz Contactless

R10E, RP10E, R15E, RP15E, R40E, RP40E, RK40E, RPK40E

R10MA, RP10MA, RP15MA, R40MA, RP40MA, RPK40MA

www.hidglobal.com/PLT-03687

Scan the QR code or visit the link to see

the multi-language electronic version of

this document.

Lisez le code QR ou suivez le lien pour

consulter la version française de ce

document.

Escanee el código QR o visite el vínculo

para consultar la versión en Español de

este documento.

Scannen Sie den QR-Code oder öffnen

Sie den Link für die deutsche Version

dieses Dokuments.

Faça a leitura do código QR ou acesse

o link da versão em português deste

documento.

Supplied parts

iCLASS SE/multiCLASSS SE Reader (1)

Installation Guide (1)

0.138-20 x 1.5" screws (2) – for installing the

reader directly to a wall (no junction box)

0.138-32 x 0.375" screws (3) – for Imperial

(US) junction box installation (2) and

attaching the reader to the back plate (1)

Recommended parts (not supplied)

Cable, 5-9 conductor (Wiegand or

Clock-and-Data), 4 conductor Twisted

Pair Over-All Shield and UL approved,

Belden3107A or equivalent (OSDP)

Certified DC power supply

Metal or plastic junction box

Security tool HID 04-0001-03 (for

anti-tamper screw)

reserved. HID, the HID Brick logo, the Chain Design, iCLASS SE,

and multiCLASS SE are trademarks or registered trademarks of

HID Global, ASSA ABLOY AB, or its affiliate(s) in the US and other

countries and may not be used without permission. All other

trademarks, service marks, and product or service names are

trademarks or registered trademarks of their respective owners.

Optional features

Open Collector Output - Controls an external device (5 VDC) operating in Host Mode only. Sink –

40mA / Source – 1mA.

Optical Tamper (enabled by default on most readers) – A configuration card may be necessary

to activate the Optical Tamper. Once activated, when the mounting plate is removed, the optical

tamper will sink to ground from its default 5VDC. Contact HID Technical Support for Optical Tamper

options.

Configuration Cards – With the use of purchasable configuration cards, the reader can be modified

to meet the specific requirements of an installation. Configuration options include; audio visual, CSN

outputs and keypad outputs (keypad models only). Contact HID Technical Support for part number

assistance to order a configuration card, if necessary.

Hold Input – when asserted, this line either buffers a card (default) or disables a card read until

released, as configured.

Mount the backplate

ATTENTION

Observe precautions for handling

ELECTROSTATIC SENSITIVE DEVICES

For Imperial (US):

Use supplied 0.138-32 x 0.375" screws

For Metric (EU etc):

Use supplied M3.5 x 12mm screws

hi dg l ob a l .com

PLT-01579, Rev. A.6

Scansiona il codice QR o visita il

link della versione Italiana di questo

documento.

Отсканируйте QR-код или пройдите по

ссылке, чтобы получить версию этого

документа на русском языке.

扫描QR码或访问此文档的中文版本的链接。

この文書の日本語版を表示するには、 QRコー

ドをスキャンするか、リンクをクリックします。

QR코드를 스캔하거나 링크를 방문하면 이

문서의 한국어 버전을 볼 수 있습니다.

M3.5 x 12mm screws (2) – for Metric (EU etc)

junction box installation

0.138-32 x 0.375" security screw (1) –

alternative security screw for attaching the

reader to the back plate

7-pin Terminal connectors (2 – only included

with Terminal Strip models)

Drill with various bits for mounting hardware

Mounting hardware

Reader spacer when mounting on or near

metal or metal junction boxes (refer to How

to Order Guide)

IP65 Mounting gasket, recommended for

outdoor installation

Junction box

not included

Optional gasket

An ASSA ABLOY Group brand

Wire the reader

Pigtail version

18"

(0.46m)

PIGTAIL***

TERMINAL

Yellow

P1-1

Beeper Input

Orange

P1-2

LED Input (GRN)

Black

P1-3

Ground (RTN)

Red

P1-4

+VDC

Drain

P1-5

Unused

Brown

P1-6

LED Input (RED)

Blue

P1-7

Hold Input

Red/Green

P2-7

GPI01/OSDP (RS485-FDX/HDX-A)

Tan

P2-6

GPI02/OSDP (RS485-FDX-HDX-B)

Violet

P2-5

*Open Collector Output/Tamper

White

P2-4

**Wiegand Data 1 / Clock

Green

P2-3

**Wiegand Data 0 / Data

Pink

P2-2

GPI03 (RS485-FDX-Z)

Gray

P2-1

GPI04 (RS485-FDX-Y)

Note: Previous iCLASS readers had reversed RS-485 wiring (P2-7 & P2-6 - A & B). When

upgrading to an iCLASS SE reader, ensure proper connections as defined below.

Note: It's possible to reuse existing Wiegand wiring for OSDP, however, using simple stranded

cable typical of Wiegand access control readers is usually not meeting the RS485 twisted pair

recommendations.

Note: For OSDP cable lengths greater than 200ft. (61M) or EMF interference, install 120Ω +/- 2Ω

resistor across RS-485 termination ends.

Note: Wiring the reader incorrectly may permanently damage the reader.

Note: With a keypad reader, operating as 26 bit emulation; upon power up you have 5 seconds

to enter the facility code followed by #. If unsuccessful, the reader LED displays solid Red.

Power-cycle the reader and retry entering the facility code.

The facility code needs to be manually entered as 3 digits (i.e. if facility code is 10 enter 0-1-0-

#). Note: SE readers only use facility codes between 1-255, and there is no default facility code.

Once the facility code has been entered, the LED will display Violet and then to a final Red. Then

power-cycle the reader. Note: When using a keypad, if there are 2 short beeps after entering your

PIN, the reader does not have a facility code configured yet. In this event, an Admin will need to

be power-cycle the reader and enter the facility code before the reader will accept your PIN.

Secure the reader to the backplate

Power and test the reader

Turn on the power.

The reader should

beep three times

and the light bar

should flash three

times.

Terminal Strip version

BEEP

GRN

GND

+VDC

DRAIN

RED

HOLD

DESCRIPTION

* Tamper Output. When

activated, output syncs to

ground (default).

** Dependent upon

reader configuration.

See HTOG Wiegand

and Clock-and-Data

configurations for more

information.

*** For 5 meter pigtail readers

(PN: 9xxxxxLEKxxxxx),

follow the wiring diagram

on the reader.

1. Align the top of the reader with the top of the

backplate.

2. Align the bottom of reader with the bottom of

the backplate.

3. Secure the reader to the backplate using one of

the supplied screws:

Security/non-tamper screw:

0.138-32 x 0.375" screw (supplied)

Non-security/standard screw: 0.138-32 x 0.375"

screws (supplied)

Test the reader with

a card. The buzzer

should beep and the

LED should flash.

GPI01

GPI02

OC/TMPR

DATA1/CLK

DATA0/DATA

GPI03

GPI04