Automation Direct ATLAS ATM1500 Quick Installation Manual - Page 3

Browse online or download pdf Quick Installation Manual for Monitor Automation Direct ATLAS ATM1500. Automation Direct ATLAS ATM1500 4 pages. Industrial flat panel pc monitor

Print Page

5. Connect Power to the Monitor

• Power source needs to be 100 - 240 VAC, 50/60 Hz.

• See power connection diagram to the right.

• Secure plug retention screws to monitor.

• Power should not be applied until all cables are attached and the

monitor is ready to operate.

: Damage can occur if power is not properly connected.

ARNING

- E

ARNING

XPLOSION

the circuit is live unless the area is known to be free of ignitable

concentrations.

6. Apply Power to the Monitor & PC

• Press the DISPLAY POWER button on the rear of the monitor to wake the

monitor up. Pressing the DISPLAY POWER button again turns off the

backlight inverter and puts the monitor in a reduced power state but

the touch screen remains active. It is important to note that this switch

does not disconnect power from the monitor. Power is always supplied

to the internal AC/DC power supply, which in turn continually supplies

power to the internal monitor electronics and the optional touch screen

controller.

7. Install the Appropriate Touch Screen Driver

• The calibration of the touch screen occurs by a calibration utility that

installs as part of the touch screen driver installation process.

• Applies to touch screen version only.

• Insert the Documentation and Driver CD into the host PC's CD drive.

• If the CD does not start automatically with the window shown below

displayed, then go to Start > Run, browse to the CD's "atlas.exe" file,

open it, and click OK.

• From the Atlas screen, the user can view the Hardware User's Guide for

the monitor being used, and/or install the touch screen drivers for the

particular PC operating system being used. Before installing the drivers,

please read the Touch Screen Driver Documentation for operating

system details.

• Reboot the PC and restart the monitor to activate the driver.

• For the latest drivers go to:

http://support.automationdirect.com/products/atlas.html

8. Verify Video and Touch Screen Functionality

• Verify the monitor's video display by running a familiar program.

• If using the touch screen model, use the touch screen to navigate by

running a familiar program.

9. Adjust the Monitor OSD Settings as Required

• Press the Select (Auto Adj) control button on the rear of the panel to

initiate an automatic configuration of the screen.

• Although normally not needed, the control buttons on the rear of panel

can be used to make other adjustments to the screen.

• Consult the Hardware User's Guide, ATM-USER, on the supplied

Documentation and Driver CD for detailed usage of the OSD settings.

10. Installation Complete

- Do not disconnect equipment while

AZARD

Power Connections:

TOP VIEW

ADC P.N. ATM-AC-CON or

PHOENIX CONTACT P.N. 1777992

FRONT VIEW

L N

Warning - Explosion Hazard - Substition of any components may

impair suitability for Class 1, Division 2.

LCD Power Button:

WARNING – Touch screen is still active while display power is off.

ATTENTION – L'écran tactile est toujours actif, méme quand l'af-

ficheur n'est pas alimenté.

ADVERTENCIA – La pantalla táctil sigue activa aún cuando el dis-

play esté apagado.

WARNUNG – Touch screen ist immer noch aktiv, während die

anzeigefläche ausgeschaltet ist.

: The monitor does not automatically select a video input

ARNING

mode. The user must press the "UP (VGA/DVI)" button on the rear

of the monitor to select either VGA or DVI input. If a "No Video"

message appears on the screen, it is also suggested the user try using

the "UP (VGA/DVI)" button to select the active video input.

OTE

ONCE YOU HAVE CONNECTED YOUR

SELECTED THE VIDEO SOURCE

SUGGESTED THAT THE

OF THE MONITOR BE PRESSED TO MAXIMIZE THE VIDEO SETTINGS

OSD Settings Main Menu:

B R I G H T N E S S / C O N T R A S T

R G B

C O L O R

P O S I T I O N

S E T U P

E X I T

1 2 8 0 X 1 0 2 4

100 VAC - 240 VAC INPUT (1.0 Amps Min)

PIN No.

1 2

Protective Earth Ground

Required Wire Specification

Wire Size

18 - 12 AWG (0.8 - 3.3 mm

Wire Material and

60 °C or 60 / 75 °C Copper

Temperature

Tightening Torque

7.0 lb·in (0.79 Nm)

Plug Retention Screws

Panel Power Draw

Power

Connection

ATM1500 (T)

Label

ATM1700 (T)

ATM1900 (T)

Power

Indicator

Display Power

Button

DISPLAY POWER

WARNING

Touch Screen is still

active while display

power is off

AND THE MONITOR

AND POWERED BOTH UNITS

"SELECT (AUTO ADJ)"

BUTTON ON THE REAR

M A I N M E N U

6 3 . 9 K H Z / 6 0 H Z

Definition

AC Line Input

AC Neutral Return

)

25 W

30 W

35 W

IT IS