Automationdirect.com IRONHORSE GSD1-48-10C User Manual - Page 9

Browse online or download pdf User Manual for DC Drives Automationdirect.com IRONHORSE GSD1-48-10C. Automationdirect.com IRONHORSE GSD1-48-10C 12 pages.

Print Page
r
w
D
eversinG
irinG
iaGraMs
c
: W
AutIoN
ResultING cuRReNt thRouGh the ARmAtuRe of the motoR does Not exceed the oveRloAd RAtINGs of the
,
dRIve
oR the demAGNetIze RAtING of the motoR beING ReveRsed
c
: e
AutIoN
Speed pots can be replaced by 0–10V analog signals (PLC, etc.). For 0–10 VDC input signal,
please refer to "Operational Description: 0 to 10 VDC Analog Reference Signal to GSD1" on
page 10."
GsD1-48-
c r
XX
eversinG
Min Speed
Max Speed
Accel
IR Comp.
Current Limit
* Inhibit Circuit (P2-4 to P2-5): 7–10 VDC @ 0.2–1 mA
Refer to "Control Inhibit Wiring Diagrams" for Control Inhibit wiring details.
c
i
w
OntrOl
nhibit
irinG
Always use a shielded cable when connecting to the inhibit terminal. The shield of the cable
should connect to the Common terminal of the DC Drive.
Speed pots can be replaced by 0–10V analog signals (PLC, etc.). For 0–10 VDC input signal,
please refer to "Operational Description: 0 to 10 VDC Analog Reference Signal to GSD1" on
page 10."
GsD1-48-
c c
XX
OntrOl
Using inhibit input
provides fast start-stop by bypassing accel circuit
Inhibit* (P2-5)
Common* (P2-4)
Pot Low (P2-3)
Pot Wiper (P2-2)
Pot High (P2-1)
** Use shielded cable when connecting to the Inhibit terminal. Connect the cable shield to the Common terminal of P2.
IronHorse GSD1 DC Drives User Manual – 2nd Edition, Revision B – 10/12/2018
heN ReveRsING A spINNING peRmANeNt mAGNet
NsuRe thAt motoR RotAtIoN hAs stopped befoRe ReveRsING the ApplIed voltAGe
w
D
irinG
iaGraM
12V Relay Coil
IN4001 thru 4007
Current
P2
Limit Trip
Inhibit* (P2-5)
-5
Output
Common* (P2-4)
-4
Pot Low (P2-3)
-3
Pot Wiper (P2-2)
-2
Pot High (P2-1)
-1
Voltage
-Arm (P1-4)
-4
Selector
+Arm (P1-3)
-3
+Battery (P1-2)
-2
-Battery (P1-1)
-1
P1
D
iaGraMs
i
w
D
nhibit
irinG
iaGraMs
SPST Switch
open = run
close = stop
P2**
* Inhibit Circuit (P2-4 to P2-5): 7–10 VDC @ 0.2–1 mA
dc
,
motoR
cAutIoN must be tAkeN thAt the
.
Optional
Inhibit *
5kΩ
Speedpot
Orange
Red
White
Fuse
Customer
supplied
SPST switch
+
or relay
+
DC Power
12/24/36/48
VDC**
Supply**
-
-
Inhibit via speedpot
provides starting and stopping through accel parameters
SPST Switch
Inhibit (P2-5)
open = stop
Common (P2-4)
close = run
Orange
Pot Low (P2-3)
Red
Pot Wiper (P2-2)
White
Pot High (P2-1)
P2**
.
Customer supplied
3PDT Center-off
Center-blocked switch
Motor
** Select battery / power voltage
as required per application
and model specifications.
5k Ω
Speedpot
dc
Page 9