Gakken Mechamo Inchworm Instructions For Assembling And Operating - Page 5
Browse online or download pdf Instructions For Assembling And Operating for Toy Gakken Mechamo Inchworm. Gakken Mechamo Inchworm 10 pages.
Figureー
7
7
Attach B6 vertical crank to the hinder part of the body.
Attach B6 vertical
crank to the body
assembled at
6
Figureー by
putting through the
B3 threaded long
pipe and fastening
both ends with
screws.
The placement of the body
and the vertical crank bar
1
A2
A1
B3
the fore part
B6
A2
the front side
B6
crank bar
3
Attaching Battery Boxes
※There are some more numbers of screws, washers,
PARTS
Parts to be used
C
nuts and bushes included for spare than are actually used.
C1
C2
battery box holder
battery box holder
C1 ・ C2は、 違う部品です。
C4
C5
Two 48×6mm pipes
One 52×4mm threaded long pipe
C6
One 70×4mm threaded long pipe
注意★メカモが動いているときは絶対にさわらないでください。たいへん危険
Warning ★ Do not touch the Mechamo while it is operating.
です。特に、小さいお子さんには、絶対にさわらせないようにしてください。
It is very dangerous. Particularly, never let small children touch it.
Raise the B1 crank bars up.
the switch of the light sensor
the back side
A1
body
B3
threaded long pipe (60×4mm)
screw (8mm)
washer
B6
vertical crank
body
washer
screw (8mm)
the hinder part
C3
Two battery boxes
Four
self-tapping screws
Four
washers
Four 8mm screws
※Check the length of screws with this figure.
Figureー
8
8
Attach the C1 and the C2 battery box holders
Attach the C1 and the
to the C3 battery boxes one by one.
C2 battery box holders
to the C3 battery boxes.
self-tapping screw
How to put batteries
Loosen the screw with a
screwdriver and open the lid.
Set batteries in the right
way and screw the lid.
C2
battery box holder
screw
C1 ・ C2は、 違う部品です。
正しくセッ トしてください。
Do not
mistake the
positive and
negative terminals.
Remove the batteries
when not using the
machine for a long time.
9
Attach the C2 battery box holder to the fore part
Also, oxyride dry cell
batteries are unsuitable
of the body.
because they are too
Taping B1 and B2 crank
powerful.
bars temporarily makes
the work easier.
9
Figureー
22
Remove the tape at .
なおクランクバーの重なりを
Attach the C2
間違えないようにしてください。
battery box holder
the hinder part
with a battery box to
B6
the fore part of the
vertical crank
body.
A1
body
The placement of the
the back side
fore part of the body
and the C2 battery
C5
box holder
threaded long pipe
(52×4mm)
A1 ・ 2
C2
washer
C5 C4
C1
battery box holder
screw (8mm)
C3
battery box
Full-scale
※Check the size with this.
connector
C4
pipe (48×6mm)
C5
threaded long pipe (52×4mm) (1)
connector
self-tapping screw
self-tapping screw
C1
battery box holder
C3
battery boxes
Taping B1 and B2 crank
bars temporarily makes
the work easier.
Remove the tape at .
22
なおクランクバーの重なりを
間違えないようにしてください。
the front side
A2
body
the fore part
screw (8mm)
washer
C4
pipe (48×6mm)
C2
battery box holder
※When the C5 threaded
long pipe doesnユt fit in the
hole in the C4 pipe, loosen
the self-tapping screw
fastening the battery box
to adjust the position
of the hole.
Be careful because these parts come off easily.