ADEMCO VISTAKEY Installation And Setup Manual

Browse online or download pdf Installation And Setup Manual for Control Unit ADEMCO VISTAKEY. ADEMCO VISTAKEY 2 pages. Single-door access control module

Print Page

GENERAL INFORMATION

The VistaKey is a single-door access control module that,

when connected to a Fire/Burglary Alarm System, provides

access control to the protected premises. The VistaKey

Module, when obtained separately, must be mounted

in the VistaKey-SK (Starter Kit) as an add-on unit to

provide access control to more than one point.

The UL Listed VistaKey-SK contains all of the components

necessary for a minimum access point configuration

installation (with exception of mag locks or door strikes).

The VistaKey module contains three zones.

These zones should be ONLY used for access

U L

control functions in UL installations. THESE

INPUT ZONES ARE NOT TO BE USED FOR

FIRE AND BURGLARY APPLICATIONS.

Do not use the VistaKey on an alarm panel that is

connected to a PassPoint Access Control System

via a VISTA Gateway Module.

VISTAKEY FEATURES

VistaKey features are as follows:

• Each VistaKey communicates with the alarm system

control via a special global polling protocol of the Vplex

polling loop.

• In the event local power to the VistaKey is lost, the

VistaKey module provides backup monitoring of the

access point door via a built-in Vplex device that is

powered solely from the polling loop. A serial number

label is affixed to the VistaKey module for manual entry

of its serial number.

• All configurable options for each VistaKey are

accomplished via software, firmware, and nonvolatile

memory, eliminating the need for PC board jumpers.

• Access point zone numbers (1-15) are assigned via a

user-friendly, 16-position rotary switch.

• Diagnostic LEDs (2) on board for relay activity and

microprocessor working condition.

COMPATIBLE FIRE/BURGLARY ALARM SYSTEMS

Refer to your VistaKey-SK manual for compatible alarm

systems that the VistaKey can interface with.

MOUNTING THE VISTAKEY

This section provides brief instructions for the initial

installation of the VistaKey module. If you require more

detailed installation information, please refer to the

procedures in section 3 of the UL Listed VistaKey-SK

(Starter Kit) manual.

Mounting and Connecting

1. Remove the front cover from the VistaKey.

INSTALLATION AND SETUP GUIDE

Single-Door Access Control Module

2. The VistaKey uses plug-in terminal blocks for TB-1 and

TB3. Keeping the terminal block screws toward the

outside edge of the VistaKey printed circuit board, slide

the terminal blocks onto the pins extending from the

board.

3. When adding a VistaKey module in the VistaKey-SK,

install the unit on the mounting plate as indicated in the

manual.

4. If applicable, mount the Door Status Monitor (DSM)

and/or Request to Exit (RTE) devices.

5. Using Figure 1 at the end of this section as a reference,

connect the card reader interface cable to TB3, making

the +5v or +12v connection last.

6. Connect the leads to VistaKey TB1 in the following

order:

a. All ground leads to terminals 2, 5, and 9).

b. The (optional) DSM, RTE, and General Purpose leads

to terminals 6, 7, and 8, respectively.

c. Door strike (or mag lock) lead to the relay Pole

terminal 10.

d. Local +12v supply lead to terminal 1 from the power

supply terminal 7.

e. Local supply lead to the N/C relay terminal 11 (if a

mag lock is being used), OR to the N/O relay terminal

12 (if a door strike is being used).

7. Connect the – polling loop and + polling loop leads (from

the alarm control panel) to terminals 4 and 3,

respectively.

8. Set the Address Select switch to the desired access door

number (1-15).

9. Repeat steps 2 through 8 for each VistaKey being

installed in your VistaKey-SK.

For complete system installation instructions, consult your

VistaKey-SK manual.

CONNECTING THE CARD READER

Lead from

Reader

Green LED

Ground*

DATA 1 (Clock)

DATA 0 (Data)

+5VDC†

+12VDC†

* TB-3 Terminal 5 is also a ground and may be used instead of

terminal 2. Terminals 2 and 5 are a common ground.

† Connect to +5VDC OR +12VDC per reader manufacturer's

specification.

K5312 4/00

VistaKey

Lead

To VistaKey

Color

TB3 Terminal #

Orange

Black

White

Green

Red†