Dynamis D40 Owner's Manual - Page 11

Browse online or download pdf Owner's Manual for Musical Instrument Amplifier Dynamis D40. Dynamis D40 11 pages.

Print Page

Dynamis

R E V V |

D 4 0

FOOT

CONTROLLER

The Revv footswitch can be configured to either

operate as a normal footswitch (with some bonuses) or

a tool to quickly recall presets on the amplifier.

Control Mode:

Select between channels, FX loop on/

off, and master volumes.

Preset Mode:

Select combinations of channel and

functions + master volume select & FX Loop on/off that

can be recalled with one button press.

Note: To switch between modes, press & hold the

footswitch button 1 for 2 seconds. The LEDs will all

illuminate, then switch to the settings in the other mode.

All settings will be retained when switching between

modes.

HOOK UP

The footswitch is connected to the rear of the amplifier

with a 5 PIN DIN Cable. The amplifier & footswitch

will work with any 5 PIN DIN cable should you be in a

pinch, but the Revv cable is always recommended for

best performance.

It is recommended that the footswitch be connected

to the amp with the power off, but should you plug it

in during amplifier use, it will power up & automatically

set itself to the amps current settings. Upon power-

up, all LEDs will turn on for a couple of seconds as it

initializes. Once complete, the foot pedal will set itself

to the amplifier's current configuration.

CONTROL MODE

The foot pedal will always power up in control mode.

This mode works similarly to most other foot pedals - it

simply controls the functions of the amp. Here is how

the buttons respond in control mode:

BUTTON 1

This button has 3 functions, it switches to channel

one when the amp is not in channel one, switches

between clean and clean boost & switches between

foot pedal modes when held for 2 seconds (control

& preset).

BUTTON 2

This button will switch to channel two when the amp is

not in channel two. It will also toggle through Channel

2 boost when in the amp is in channel 2.

BUTTON 3

This button toggles FX Loop In/Out.

BUTTON 4

This button toggles between master volumes.

BUTTON 5

This button toggles FX Loop In/Out.

PRESET MODE

When the footswitch is in preset mode, each button

can then be used to save amp settings, much like a

MIDI program change command. For example, if you

wanted to save an amp setting like ch2, boost on,

bright: on, FX loop: in, Master volume: 2, you could

save this all to one button! Then every time you want

to use this amp configuration, all you would have to do

is press that one button & the amp would change to

this setting.

Each button on the foot controller can save settings.

They can also save digital cabs utilizing the Two Notes

Torpedo tech inside!

Note 1: When a preset is set on the footswitch, it will not

be lost if power is removed from the amp. The Revv

footswitch has memory & will retain the settings. Each

button is identical in Preset mode & will be considered

banks. Each bank can hold an amp preset.

Note 2: Button one, however, have 2 functions in preset

mode. Button one will switch between the modes

(Control & Preset). Holding the button for 2 seconds will

activate the abilities.

TO SAVE A PRESET TO A BANK

1. Put the footswitch in preset mode & select the bank

you want to save to (Buttons one through four).

2. Set the amplifier to your desired configuration from

the front panel of the amp.

3. The bank LED on the footswitch you have selected

will begin to blink stating a change has been made

on the front panel of the amp.

4. Once you're finished configuring the amp, simply

press the desired bank button on the footswitch to

save the setting into that bank & you're done! The

LED will stop flashing verifying that the change has

been saved. Now every time you press that bank

button, the amp will switch to the configuration you.

Note: Any change made on the front panel of the amp

will result in a bank LED blinking which means that the

current bank setting is different from that of the amps

new configuration. To save the new setting press the

bank button on the footswitch (blinking LED), or, to reset

the configuration & not keep the change, simply press

another bank button & the change will NOT be saved.

FOOT CONTROLLER RESET

The footswitch memory can be cleared when it is

needed. Each of the 4 banks will be returned to factory

defaults. To reset the memory & return the unit to

factory defaults, begin with the amplifier's power off &

the footswitch plugged into the footswitch jack on the

amplifier.

Next, press & hold buttons 1 & 2 down & turn the power

switch to the ON position on the amplifier. As soon

as the footswitch powers up, it will return all memory

R E V V |

locations to factory defaults as long as buttons one &

two were held down properly at power-up.

Note: This will erase all your settings from the foot

controllers memory!

USA & CANADA COMPLIANCE

For USA:

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation. This equipment

complies with FCC radiation exposure limits set forth for an uncontrolled

environment. End-users must follow the specific operating instructions for

satisfying RF exposure compliance. This transmitter meets both portable and

mobile limits as demonstrated in the RF Expo-sure Analysis. This transmitter

must not be co-located or operating in conjunction with any other antenna

or transmitter except in accordance with FCC multi-transmitter product

procedures.

For Canada:

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate

using an antenna of a type and maximum (or lesser) gain approved for

the transmitter by Industry Canada. To reduce potential radio interference

to other users, the antenna type and its gain should be so chosen that

the equivalent isotropically radiated power (e.i.r.p.) is not more than that

necessary for successful communication.

Dynamis

D 4 0