Dynamite Passport Ultra 220W Installation Manual - Page 5

Browse online or download pdf Installation Manual for Battery Charger Dynamite Passport Ultra 220W. Dynamite Passport Ultra 220W 10 pages. 100w lcd ac/dc multi-chemistry battery charger

Print Page
Dynamite Passport Ultra 220W Installation Manual
CAUTION: The nickel charge program menus are to be used ONLY for the charging and discharging of nickel battery packs. Charging other battery types using the nickel charge programs will
damage the battery or the charger.

5 - NICkEL (NI-Mh/NI-CD) ChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–)
and Power Output Red (+), making sure that the positive and negative connectors are not
reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Ni-MH/Ni-Cd.
Program select=NiMH
CHG
4. Press CHG.
NiMH CHARGE
Capacity
Current
CHG Mode
Press&Hold
BACK
5. Press a parameter to highlight that parameter.
6. Press the Up and Down Arrows to edit the parameter.
7. Press Select to save the parameter.
8. Once the parameters are at the desired settings, press and hold CHARGE.
9. The charger will check the battery and charger settings and charging will begin. The charger
will beep and display the following screen:
NiMH CHG
Capacity
Current
Voltage
Resistance
Peak Temp.
10. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Charging
information.
11. Press Graph to see the battery voltage graph. Press Back to return to the charging screen.
Data NiMH = Graph
12. Press STOP at any time to stop charging.
13. When charging is complete, the charger will sound a series of beeps and display the following
screen:
NiMH DONE
Capacity
Current
Voltage
Resistance
Peak Temp.
14. Disconnect the battery from the charger.
5
Only Ni-MH is shown in the following three sections.
N i M H
DCHG
CYCLE
:
50mAh
:
0.1A
:
Man
:
CHARGE
SELECT
000:09S
:
2mAh
:
1.8A
:
7.98V
:
****mΩ
:
No sens
026:01S
:
671mAh
:
0.0A
:
9.25V
:
14mΩ
:
No sens

6 - NICkEL DISChArgINg

1. Connect the banana plugs of the battery adapter cable to the Power Output Black (–)
and Power Output Red (+), making sure that the positive and negative connectors are not
reversed.
2. Connect the battery connector to the battery adapter cable.
3. Press the Left and Right Arrows on the LCD Touch Screen to scroll through the main menu
screens until you reach Program Select=Ni-MH/Ni-Cd.
Program select=NiMH
CHG
4. Press DCHG.
NiMH DISCHARGE
End Volt
Capacity
Current
Press&Hold
BACK
5. Press a parameter to highlight that parameter.
6. Press the Up and Down Arrows to edit the parameter.
7. Press Select to save the parameter.
8. Once the parameters are at the desired settings, press and hold DISCHRG.
9. The charger will check the battery and charger settings and discharging will begin. The charger will
beep and display the following screen:
NiMH DCHG
Capacity
Current
Voltage
Resistance
Peak Temp.
10. Press the arrow in the top right of the LCD Touch Screen to see the rest of the Discharging
information.
11. Press Graph to see the battery voltage graph. Press Back to return to the discharging screen.
Data NiMH = Graph
8.39V
12. Press STOP at any time to stop discharging.
13. When discharging is complete, the charger will sound a series of beeps and display the
following screen:
NiMH DONE
Capacity
Current
Voltage
Resistance
Peak Temp.
14. Disconnect the battery from the charger.
N i M H
DCHG
CYCLE
:
0.10V
:
50mAh
:
0.1A
:
DISCHRG
SELECT
000:34S
:
16mAh
:
1.8A
:
8.43V
:
****mΩ
:
No sens
000:47S
026:01S
:
671mAh
:
0.0A
:
9.25V
:
14mΩ
:
No sens