Dynamite Prophet Precept Instruction Manual - Page 2

Browse online or download pdf Instruction Manual for Battery Charger Dynamite Prophet Precept. Dynamite Prophet Precept 2 pages. 80w lcd ac/dc multi-chemistry battery charger

Print Page

Dynamite Prophet Precept Instruction Manual

NICkEL-CAdMIUM (NI-Cd) BATTERIES

Press the Battery Type/Memory Button (H) to change among the 7 main menu

screens and go to the PROGRAM SELECT Ni-Cd BATT screen. Press the Select/

NiCd 2.0A 7.59V

Start Button (k) to enter this menu. This is the menu in which you set the standard

CHG 022:43 01082

Ni-Cd battery charge parameters.

PROGRAM SELECT

NiCd BATT

A. A Ni-Cd battery pack is charging

B. Charging rate is 2.0A (2000mAh)

Change other Ni-Cd battery charging settings as needed in the USER SET menu.

C. Voltage being applied to the battery is currently 7.59V

Refer to the PROgRAM SELECT USER SET section.

d. Present charge level of the battery is 1082mAh

E. Time elapsed since the charge process started is 22:43

Press the down (–) Button (I) or Up (+) Button (J) to go to one of the control

screens (CHARgE, DISCHARgE or CYCLE) to do what your battery needs. Correctly

During charging, the down (–) Button or Up (+) Button can be pressed to show

connect your Ni-Cd battery to the charger. Press the Select/Start Button (k) and

several parameter messages on the LCD screen including: Ni-Cd Sensitivity, Capacity

adjust charging parameters as needed. Press and hold the Select/Start Button

Cut-off, Safety Timer setting, Temperature Cut-off, External Temperature and Input

(approximately 3 seconds) until the screen changes to start the battery check/charge

Power Voltage. The charger signals when the charging (or discharging) process is

sequence. After confirmation, charging starts and information will show on the LCD

complete (if Buzzer is set to ON).

screen.

Press the Battery Type/Memory Button at any time to stop charging (or discharging).

CAUTION: The Ni-Cd charge program menus are to be used ONLY for the charging and discharging of Ni-Cd battery packs. Charging other battery types using the

Ni-Cd charge programs will damage the battery or the charger.

NI-Cd CHARGING

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

To select a value other than the existing parameter:

Then press the Battery Type/Memory Button until you reach the PROGRAM

• Press the Select/Start Button so the charge current value (A) flashes

SELECT NiCd BATT screen. Press the Select/Start Button (k) to enter this menu.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Press the down (–) Button (I) or Up (+) Button (J) to reach the NiCd CHARGE

charge current value

screen and set charging parameters. The charging amperage (A) can be set

• Press the Select/Start Button again to save the value

between 0.1 and 6.0A.

If no parameters are flashing, you can press the down (–) Button or Increase

NiCd CHARGE

Man

Button to select another program such as DISCHARgE or CYCLE.

CURRENT

0.1A

To start charging, press and hold the Select/Start Button for 3 seconds.

NI-Cd dISCHARGING

A battery pack's capacity can be verified by discharging the pack to its minimum

To select values other than the existing parameters:

voltage level and measuring the current as the pack is discharged.

• Press the Select/Start Button so the discharge current value (A) flashes

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Then press the Battery Type/Memory Button until you reach the PROGRAM

discharge current value

SELECT NiCd BATT screen. Press the Select/Start Button (k) to enter this menu.

• Press the Select/Start Button again to save the value and the voltage value (B)

Press the down (–) Button (I) or Up (+) Button (J) to reach the NiCd

flashes

DISCHARGE screen and set discharging parameters. The discharging amperage (A)

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

can be set between 0.1 and 2.0A. The discharge level (B) can be set for AUTO or

voltage

from 0.1 to 25.0V.

• Press the Select/Start Button again to save the voltage value

NiCd DISCHARGE

If no parameters are flashing, you can press the down (–) Button or Increase

0.1A

AUTO

Button to select another program such as CHARgE or CYCLE.

To start discharging, press and hold the Select/Start Button for 3 seconds.

NI-Cd CyCLE CHARGING

The battery can be put through a series of charge/discharge cycles using this

To select values other than the existing parameters:

program. Cycling Ni-Cd batteries can increase capacity and rejuvenate neglected

• Press the Select/Start Button so the cycle type (A) flashes

batteries. Discharge capacity and average battery voltage help you compare batteries

• Press the down (–) Button or Up (+) Button to set the cycle type as

for the best run time and power.

CHG>DCHG or DCHG>CHG

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

• Press the Select/Start Button again to save your choice and the number of

Then press the Battery Type/Memory Button until you reach the PROGRAM

cycles (B) flashes

SELECT NiCd BATT screen. Press the Select/Start Button (k) to enter this menu.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Press the down (–) Button (I) or Up (+) Button (J) to reach the NiCd CYCLE

cycle count between 1 and 5

screen and set charge/discharge cycle count parameters.

• Press the Select/Start Button again to save the cycle count value

NiCd CYCLE

If no parameters are flashing, you can press the down (–) Button or Increase

DCHG>CHG

Button to select another program such as CHARGE or DISCHARGE.

To start cycling, press and hold the Select/Start Button for 3 seconds.

LEAd-ACId/SEALEd-LEAd-ACId (PB) BATTERIES

Press the Battery Type/Memory Button (H) to change among the 7 main menu screens

and go to the PROGRAM SELECT Pb BATT screen. Press the Select/Start Button (k) to en-

Pb–6 4.0A 12.39V

ter this menu. This is the menu in which you set the standard Pb battery charge parameters.

CHG 022:43 01082

PROGRAM SELECT

Pb BATT

A. A Pb battery pack is charging

The nature of a Lead-Acid or Sealed-Lead-Acid battery is very different from that of

B. Battery pack has 6 cells in series

Lithium, Ni-MH or Ni-Cd batteries. The output current of a Pb battery is lower than

C. Charging rate is 4.0A (4000mAh)

other batteries relative to their capacities. Furthermore, lead-acid batteries can't be

d. Voltage being applied to the battery is currently 12.39V

charged at a level greater than 1/10 their capacity. For example, a 5000mAh lead

E. Present charge level of the battery is 1082mAh

acid battery can't be charged at a rate greater than 0.5A. For more details on the

f. Time elapsed since the charge process started is 22:43

charge and discharge capabilities of your battery, please refer to the charging data

During charging, the down (–) Button or Up (+) Button can be pressed to show several

supplied by the battery manufacturer.

parameter messages on the LCD screen including: End Voltage, Capacity Cut-off, Safety

Press the down (–) Button (I) or Up (+) Button (J) to go to one of the control

Timer setting, Temperature Cut-off, External Temperature and Input Power Voltage. To

screens (CHARgE or DISCHARgE) to do what your battery needs. Correctly connect

change the charging rate during charging, press the Select/Start Button, then increase

your Pb battery to the charger. Press the Select/Start Button (k) and adjust charg-

or decrease the rate using the down (–) Button and Up (+) Button. The charger signals

ing parameters as needed. Press and hold the Select/Start Button (approximately 3

when the charging (or discharging) process is complete (if Buzzer is set to ON).

seconds) until the screen changes to start the battery check/charge sequence. After

Press the Battery Type/Memory Button at any time to stop charging (or discharging).

confirmation, charging starts and information will show on the LCD screen.

CAUTION: The Pb charge program menus are to be used ONLY for the charging and discharging of Pb battery packs. Charging other battery types using the Pb

charge programs will damage the battery or the charger.

PB CHARGING

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

To select values other than the existing parameters:

Then press the Battery Type/Memory Button until you reach the PROGRAM

• Press the Select/Start Button so the charge current value (A) flashes

SELECT Pb BATT screen. Press the Select/Start Button (k) to enter this menu.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Press the down (–) Button (I) or Up (+) Button (J) to reach the Pb CHARGE

charge current value

screen and set charging parameters. The charging amperage (A) can be set between

• Press the Select/Start Button again to save the value and the voltage value (C)

0.1 and 6.0A. Voltage (C) is dependent on the number of cells in series (B) and can

flashes

be set between 2.0 (for 1P batteries) to 20.0V (for 10P batteries).

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Pb CHARGE

voltage (and # of cells in series (B))

0.1A

2.0V(1P)

• Press the Select/Start Button again to save the voltage value

If no parameters are flashing, you can press the down (–) Button or Increase

Button to select another program such as DISCHARGE.

To start charging, press and hold the Select/Start Button for 3 seconds.

PB dISCHARGING

A battery pack's capacity can be verified by discharging the pack to its minimum

To select values other than the existing parameters:

voltage level and measuring the current as the pack is discharged.

• Press the Select/Start Button so the discharge current value (A) flashes

Press the Battery Type/Memory Button (H) until you reach the 7 main menus.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

Then press the Battery Type/Memory Button until you reach the PROGRAM

discharge current value

SELECT Pb BATT screen. Press the Select/Start Button (k) to enter this menu.

• Press the Select/Start Button again to save the value and the voltage value (C)

Press the down (–) Button (I) or Up (+) Button (J) to reach the Pb DISCHARGE

flashes

screen and set discharging parameters. The discharging amperage (A) can be set

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

between 0.1 and 2.0A. Voltage (C) is dependent on the number of cells in series (B)

voltage (and # of cells in series (B))

and can be set between 2.0 (for 1P batteries) to 20.0V (for 10P batteries).

• Press the Select/Start Button again to save the voltage value

Pb DISCHARGE

If no parameters are flashing, you can press the down (–) Button or Increase

0.1A

2.0V(1P)

Button to select another program such as CHARGE.

To start discharging, press and hold the Select/Start Button for 3 seconds.

SAVE dATA

• Press the Select/Start Button to save the value and the battery capacity (C) flashes

PROGRAM SELECT

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the

SAVE DATA

battery capacity

• Press the Select/Start Button to save the value and the battery profile value flashes

Press the Battery Type/Memory Button (H) to change among the 7 main menu

• Press and hold the Select/Start Button for at 3 seconds until the screen

screens and go to the PROgRAM SELECT SAVE DATA screen. Use this menu to save a

battery profile. To reduce the time required to initiate a charging or discharging cycle on a

changes to the CHARGE menu

battery you regularly use, this charger has been designed with the capability of storing up

• Press the Select/Start Button to set the CHARGE parameters. Refer to the bat-

to 5 battery profiles that can be quickly accessed and run using the Load Data menu.

tery type parameter setting instructions

• Press the down (–) Button or Up (+) Button to go to and set other

SAVE [01]

parameters (BALANCE CHARgE, DISCHARgE, etc.)

2.0V

5000mAh

After setting all parameters, press and hold the Select/Start Button for 3 seconds

until the screen changes.

• Press the Select/Start Button (k) to enter this menu

• Press the down (–) Button (I) or Up (+) Button (J) to select a battery profile

(A) (1 through 5)

• Press the Select/Start Button to save the battery profile value so the battery

After the battery profile has been saved, the charger will return to the PROGRAM

type (B) flashes

SELECT SAVE DATA screen.

• Press the down (–) Button or Up (+) Button to select a battery type

Enter the Save Data menu and create more battery profiles or press the Battery

• Press the Select/Start Button to save the battery type and the voltage value (d) flashes

Type/Memory Button to go to other options.

• Press the down (–) Button or Up (+) Button to DECREASE or INCREASE the voltage

LOAd dATA

• Press the Select/Start Button (k) and the battery profile value (A) flashes

PROGRAM SELECT

• Press the down (–) Button (I) or Up (+) Button (J) to DECREASE or INCREASE

LOAD DATA

the battery profile value

• Press and hold the Select/Start Button until the battery charging function

Press the Battery Type/Memory Button (H) to change among the 7 main menu

screen shows

screens and go to the PROgRAM SELECT LOAD DATA screen. Use this menu to load

a saved battery profile.

• Press the down (–) Button or Up (+) Button to go to the charging function you

need

LOAD [01]

LiPo

• Press and hold the Select/Start Button to start the chosen charging function

11.1V

5000mAh

PROGRAM SELECT USER SET

USER SET

PROGRAM–>

Press the Battery Type/Memory Button (H) to change among the 7 main menu screens and go to the USER SET PROgRAM–> screen. Use this menu to set up program-

ming as desired for charging your batteries. USER SET programming lets you change from default settings for "behind the scenes" operating parameters for this charger.

At the USER SET PROgRAM-> screen, press the Select/Start Button (k) to enter the menu. Press the down (–) Button (I) or Up (+) Button (J) to change between

sub-menu screens. Press the Battery Type/Memory Button to return to the main menu screen.

LITHIUM BATTERy TyPE

LITHIUM BATTERy CHECk TIME

Use this menu to choose lithium battery type: Li-Po, Li-Io or Li-Fe, which shows on

other Lithium battery screens.

LiPo

Use this menu to set a time limit on a lithium battery check. The battery charger can

V. Type

3.7V

automatically identify the number of series cells in a lithium battery pack. Normally

this checking process is very quick; however, it will not work properly if the battery

• Press the Select/Start Button so the voltage value (A) flashes

pack is damaged or over-discharged. Very large capacity packs will also take longer

to check. To prevent errors, the charger default is to spend up to 10 minutes to

• P ress the down (–) Button or Up (+) Button to change the voltage value

identify the number of cells. Time limit can be between 5 and 60 minutes.

(changing voltage value changes lithium battery type): 3.7V for Li-Po, 3.6V for

To select a value other than the default parameter:

Li-Ion and 3.3V for Li-Fe

• Press the Select/Start Button to save your selection

• Press the Select/Start Button so the time value (A) flashes

• P ress the down (–) Button or Up (+) Button to DECREASE or INCREASE the

time value

• Press the Select/Start Button again to save this value

NI-MH SENSITIVITy (PEAk VOLTAGE)

NI-Cd SENSITIVITy (PEAk VOLTAGE)

NiMH Sensitivity

D.Peak

Default

Use this menu to adjust peak voltage level (D.Peak) at which the charging stops

Use this menu to adjust the peak voltage level (D.Peak) at which charging stops

for a Ni-Cd battery pack. The D.Peak value is adjustable between 5mV/Cell and

for a Ni-MH battery pack. The D.Peak value is adjustable between 5mV/Cell and

20mV/Cell. generally, 10mV/Cell is a good choice for Ni-Cd batteries. When this

20mV/Cell. generally, 8mV/Cell is a good choice for Ni-MH batteries. When this

value is set too high, the battery may be over-charged. When this the value is set

value is set too high, a battery may be over-charged. When this value is set too

too low, the charger will not charge a battery to full capacity.

low, the charger will not charge a battery to full capacity.

To select a value other than the default parameter:

• Press the Select/Start Button so the D.Peak value (A) flashes

• P ress the down (–) Button or Up (+) Button to DECREASE or INCREASE the

D.Peak value

D.peak value

• Press the Select/Start Button again to save this value

BATTERy CUTOff TEMPERATURE

WASTE (BATTERy COOL-dOWN) TIME

Temp Select

Temp Cut-Off 80C

Use this menu to set a cutoff temperature that can prevent damage to the battery

Use this menu to set waste time during each step in a cycle. When a Ni-MH or Ni-Cd

by stopping the charging process if the battery temperature reaches that limit.

battery is cycled (charged, discharged and charged again) it will get hot, therefore it is

The charger can be used in conjunction with a battery mounted temperature

necessary to set a waste time interval during each step of the process to make sure

sensor (sold separately, DYN5033) connected to the Temperature Sensor Port

the battery and charger are completely cooled before moving on to the next part of the

(d) to monitor the temperature of the battery during the charging process. The

cycle. Default time is 1 minute, but this can be set between 0 and 60 minutes.

temperature can be set between 20 – 80° C (68–176° F).

To select a value other than the default parameter:

• Press the Select/Start Button so the time value (A) flashes

• Press the Select/Start Button (k) so the temperature value (A) flashes

• P ress the down (–) Button or Up (+) Button to DECREASE or INCREASE the

time value

temperature value

• Press the Select/Start Button again to save this value

SAfETy TIMER

Safety Timer

180min

Use this menu to set a time limit for charging a battery. When a charge cycle is

started, a clock inside the charger will begin recording the elapsed charge time. If

the safety timer function has been turned ON, the charger will stop the charging

process once this time limit has been reached to avoid damage caused by over-

charging the battery. This time value can be set between 10 and 720 minutes.

To select values other than the default parameters:

• Press the Select/Start Button so ON or OFF (A) flashes

• P ress the down (–) Button or Up (+) Button to turn the safety timer ON or OFF

• P ress the Select/Start Button again to save this setting and the time value

(B) flashes

• P ress the down (–) Button or Up (+) Button to DECREASE or INCREASE the

time value

• Press the Select/Start Button again to save this value

BEEP ANd BUZZER SOUNd CONTROL

Key Beep

Buzzer

Use this menu to set the key beep and charger alarm buzzer at ON or OFF as

needed. We recommend that you keep the alarm ON so the alarm will sound when

charging is complete or if there is cause for alarm during charging.

To select values other than the default parameters:

• Press the Select/Start Button so ON or OFF (A) flashes

• P ress the down (–) Button or Up (+) Button to set the key beep at ON or OFF

• Press the Select/Start Button again to save this setting and ON or OFF (B) flashes

• P ress the down (–) Button or Up (+) Button to set the buzzer at ON or OFF

• Press the Select/Start Button again to save this value

SAVE...

USB dEVICE CHARGING

The charger has the capability to charge a smartphone, music player or any USB-compatible device with the 2.1A USB Power Output Port (E). To use the charging

function, simply connect a compatible charging device or cord into the charge port while the charger is powered ON. The charger provides up to 2.1A current at 5V DC.

TROUBLESHOOTING

LCD Screen Warning and Error messages shown below. During charger operation, circuits monitor battery and charger functions. If the following messages show on the

charger's LCD screen, make the recommended responses. If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer

service center for assistance.

REVERSE POLARITY

Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery

CONNECTION BREAK

Make sure the power connections are correct for charging

SHORT ERR

Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires

Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct

INPUT VOL ERR

input voltage

Incorrect setting for cell in series count (pack voltage) of a lithium battery. Make charger settings match the battery pack label cell in series count

VOL SELECT ERR

specifications or replace the battery

BREAK DOWN

Charger electronics require repair

BATTERY CHECK LOW VOLTAgE

Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery

BATTERY CHECK HIgH VOLTAgE

Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery

Battery Type

Li-Po

Standard voltage (Volts per cell)

3.70

Max. voltage (Volts per cell)

4.20

Min. voltage (Volts per cell)

3.00

LiPo/LiIo/LiFe

dyNAMITE 5-yEAR US LIMITEd CHARGER WARRANTy INfORMATION

We are so confident about the quality of our chargers we offer a 5-year replacement

CHK Time

10min

plan on all of our Dynamite Prophet and Passport chargers.

Our 5-year replacement plan requires proof of purchase (copy of the receipt) and we

do, reserve the right to deny replacement to any abusers of our plan. See below for

full details. Contact the appropriate Horizon Service Department for instructions on

warranty claims.

5-yEAR US LIMITEd WARRANTy

Warranty Period - Exclusive Warranty - Horizon Hobby, LLC ("Horizon") warrants

that the included Dynamite Prophet, or Passport charger ("Product") will be free from

defects in materials and workmanship for a period of five (5) years after the date of

purchase ("Warranty Period").

What is Not Covered - This warranty is not transferable and does not cover (i) cos-

metic damage, (ii) damage due to acts of god, accident, misuse, abuse, negligence,

commercial use, or due to improper use, installation, operation or maintenance, (iii)

modification of or to any part of the Product, (iv) attempted service by anyone other

than a Horizon Hobby authorized service center, (v) Product not purchased from an

authorized Horizon dealer, or (vi) Product not compliant with applicable technical regu-

lations.

NiCd Sensitivity

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WAR-

D.Peak

Default

RANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WAR-

RANTIES, INCLUDINg, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-

INFRINgEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

THE PURCHASER ACKNOWLEDgES THAT THEY ALONE HAVE DETERMINED THAT

THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER'S

INTENDED USE.

Purchaser's Remedy - Horizon's sole obligation and purchaser's sole and exclusive

remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any

Product determined by Horizon to be defective. Horizon reserves the right to inspect

any and all Product(s) involved in a warranty claim. Service or replacement decisions

are at the sole discretion of Horizon. Proof of purchase is required for all warranty

claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

PURCHASER'S SOLE AND EXCLUSIVE REMEDY. Replacement Products are covered

under this warranty for thirty (30) days after receipt or for the remainder of the Warranty

Period of the Product which they have replaced, whichever is longer.

Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAgES, LOSS OF PROFITS OR PRODUCTION OR

Waste Time

COMMERCIAL LOSS IN ANY WAY, REgARDLESS OF WHETHER SUCH CLAIM IS BASED

IN CONTRACT, WARRANTY, TORT, NEgLIgENCE, STRICT LIABILITY OR ANY OTHER

CHG>DCHG

1min

THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAgES. Further, in no event shall the liability of Horizon exceed the individual

price of the Product on which liability is asserted. As Horizon has no control over use,

setup, final assembly, modification or misuse, no liability shall be assumed nor ac-

cepted for any resulting damage or injury. By the act of use, setup or assembly, the user

accepts all resulting liability. If you as the purchaser or user are not prepared to accept

the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

Law - These terms are governed by Illinois law (without regard to conflict of law princi-

pals). This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state. Horizon reserves the right to change or modify this

warranty at any time without notice.

NON-US LIMITEd WARRANTy

BATTERy CAPACITy CUTOff

What this Warranty Covers - Horizon Hobby, LLC ("Horizon") warrants to the original

purchaser that the product purchased (the "Product") will be free from defects in ma-

Capacity Cut-Off

terials and workmanship at the date of purchase.

5000mAh

What is Not Covered - This warranty is not transferable and does not cover (i) cos-

metic damage, (ii) damage due to acts of god, accident, misuse, abuse, negligence,

Use this menu to set a capacity limit on when the charger stops charging a battery. When

commercial use, or due to improper use, installation, operation or maintenance, (iii)

a charge cycle starts, the charger records the battery capacity. When the capacity cutoff

modification of or to any part of the Product, (iv) attempted service by anyone other

function is set at ON, the charger will stop charging at the capacity limit to prevent battery

than a Horizon Hobby authorized service center, (v) Product not purchased from an

damage. Capacity can be adjusted between 10 and 50,000mAh.

authorized Horizon dealer, or (vi) Product not compliant with applicable technical regu-

To select values other than the default parameters:

lations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WAR-

• Press the Select/Start Button so ON or OFF (A) flashes

RANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WAR-

• P ress the down (–) Button or Up (+) Button to turn the capacity cutoff ON or OFF

RANTIES, INCLUDINg, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-

• P ress the Select/Start Button again to save this setting and the capacity

INFRINgEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

THE PURCHASER ACKNOWLEDgES THAT THEY ALONE HAVE DETERMINED THAT

value (B) flashes

THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER'S

• P ress the down (–) Button or Up (+) Button to DECREASE or INCREASE

INTENDED USE.

capacity value

Purchaser's Remedy - Horizon's sole obligation and purchaser's sole and exclusive

• Press the Select/Start Button again to save this value

remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any

Product determined by Horizon to be defective. Horizon reserves the right to inspect

any and all Product(s) involved in a warranty claim. Service or replacement decisions

are at the sole discretion of Horizon. Proof of purchase is required for all warranty

INPUT POWER LOW VOLTAGE CUTOff

claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

PURCHASER'S SOLE AND EXCLUSIVE REMEDY.

Input Power Low

Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

Cut-Off

11.0V

INCIDENTAL OR CONSEQUENTIAL DAMAgES, LOSS OF PROFITS OR PRODUCTION OR

COMMERCIAL LOSS IN ANY WAY, REgARDLESS OF WHETHER SUCH CLAIM IS BASED

Use this menu to set the input voltage limit so an alarm will sound if the voltage

IN CONTRACT, WARRANTY, TORT, NEgLIgENCE, STRICT LIABILITY OR ANY OTHER

goes below the cutoff value. The voltage alarm value can be set from 10.0 to

THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF

11.0V.

SUCH DAMAgES. Further, in no event shall the liability of Horizon exceed the individual

price of the Product on which liability is asserted. As Horizon has no control over use,

To select a value other than the default parameter:

setup, final assembly, modification or misuse, no liability shall be assumed nor ac-

• Press the Select/Start Button so the voltage value (A) flashes

cepted for any resulting damage or injury. By the act of use, setup or assembly, the user

• P ress the down (–) Button or Up (+) Button to DECREASE or INCREASE the

accepts all resulting liability. If you as the purchaser or user are not prepared to accept

voltage value

the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

• Press the Select/Start Button again to save this value

Law - These terms are governed by Illinois law (without regard to conflict of law princi-

pals). This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state. Horizon reserves the right to change or modify this

warranty at any time without notice.

WARRANTy SERVICES

questions, Assistance, and Services - Your local hobby store and/or place of pur-

chase cannot provide warranty support or service. Once assembly, setup or use of the

Product has been started, you must contact your local distributor or Horizon directly.

This will enable Horizon to better answer your questions and service you in the event

Country of Purchase

(Repairs and Repair Requests)

United States of America

(Product Technical Assistance)

United Kingdom

Horizon Technischer Service

Germany

Sales: Horizon Hobby GmbH

France

China

Li-Io

Li-Fe

Ni-MH

Ni-Cd

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

3.60

3.30

1.20

2.00

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications.

4.10

3.60

1.60

2.45

3.00

2.00

1.00

0.85

1.75

Declaration of Conformity (in accordance with ISO/IEC 17050-1)

No.

HH2014082602U1

Product(s):

Prophet Precept 80W Charger

WARRANTy SERVICES

Item Number(s): DYNC2015EU, DYNC2015UK

questions, Assistance, and Services - Your local hobby store and/or place of pur-

chase cannot provide warranty support or service. Once assembly, setup or use of the

The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the EMC Directive

Product has been started, you must contact your local distributor or Horizon directly.

2004/108/EC and LVD Directive 2006/95/EC:

This will enable Horizon to better answer your questions and service you in the event

EN55022:2010 + AC:2011

that you may need any assistance. For questions or assistance, please visit our website

EN55024:2010

at www.horizonhobby.com, submit a Product Support Inquiry at https://horizonhobby.

quickbase.com/db/bghj7ey8c?a=genNewRecord, or call the toll free telephone num-

EN61000-3-2:2006+A1:2009+A2:2009

ber referenced in the Warranty and Service Contact Information section to speak with

EN61000-3-3:2008

a Product Support representative.

EN60950-1:2006+A11:2009+A1:2010+A12:2011

Inspection or Services - If this Product needs to be inspected or serviced and is

compliant in the country you live and use the Product in, please use the Horizon Online

Signed for and on behalf of:

Service Request submission process found on our website or call Horizon to obtain a

Horizon Hobby, LLC

Return Merchandise Authorization (RMA) number. Pack the Product securely using a

shipping carton. Please note that original boxes may be included, but are not designed

Champaign, IL USA

to withstand the rigors of shipping without additional protection. Ship via a carrier

August 26, 2014

that provides tracking and insurance for lost or damaged parcels, as Horizon is not

Instructions for disposal of WEEE by users in the European Union

responsible for merchandise until it arrives and is accepted at our facility. An Online

Service Request is available at http://www.horizonhobby.com/content/_service-cen-

This product must not be disposed of with other waste. Instead, it is the user's responsibility to dispose of their waste equipment by handing it over to a designated

collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will

ter_render-service-center. If you do not have internet access, please contact Horizon

Product Support to obtain a RMA number along with instructions for submitting your

help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can

product for service. When calling Horizon, you will be asked to provide your complete

drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.

name, street address, email address and phone number where you can be reached

during business hours. When sending product into Horizon, please include your RMA

number, a list of the included items, and a brief summary of the problem. A copy of

your original sales receipt must be included for warranty consideration. Be sure your

name, address, and RMA number are clearly written on the outside of the shipping car-

ton. YOU MUST CONTACT THE APPROPRIATE HORIZON SERVICE DEPARTMENT FOR

ANY CHARgER WARRANTY CLAIM.

Warranty Requirements - for Warranty consideration, you must include your

original sales receipt verifying the proof-of-purchase date. Provided warranty

conditions have been met, your Product will be serviced or replaced free of charge.

Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service - Should your service not be covered by warranty, ser-

vice will be completed and payment will be required without notification or

estimate of the expense unless the expense exceeds 50% of the retail pur-

chase cost. By submitting the item for service you are agreeing to payment of

the service without notification. Service estimates are available upon request. You

must include this request with your item submitted for service. Non-warranty service

estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for

return freight. Horizon accepts money orders and cashier's checks, as well as Visa,

MasterCard, American Express, and Discover cards. By submitting any item to Horizon

for service, you are agreeing to Horizon's Terms and Conditions found on our website

http://www.horizonhobby.com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country

of use and ownership. If received, a non-compliant Product will not be ser-

viced. further, the sender will be responsible for arranging return shipment

of the un-serviced Product, through a carrier of the sender's choice and at

the sender's expense. Horizon will hold non-compliant Product for a period of

60 days from notification, after which it will be discarded.

that you may need any assistance. For questions or assistance, please visit our website

at www.horizonhobby.com, submit a Product Support Inquiry at https://horizonhobby.

quickbase.com/db/bghj7ey8c?a=genNewRecord, or call the toll free telephone num-

ber referenced in the Warranty and Service Contact Information section to speak with

a Product Support representative.

Inspection or Services - If this Product needs to be inspected or serviced and is

compliant in the country you live and use the Product in, please use the Horizon Online

Service Request submission process found on our website or call Horizon to obtain a

Return Merchandise Authorization (RMA) number. Pack the Product securely using a

shipping carton. Please note that original boxes may be included, but are not designed

to withstand the rigors of shipping without additional protection. Ship via a carrier that

provides tracking and insurance for lost or damaged parcels, as Horizon is not respon-

sible for merchandise until it arrives and is accepted at our facility. An Online Service

Request is available at http://www.horizonhobby.com/content/_service-center_ren-

der-service-center. If you do not have internet access, please contact Horizon Product

Support to obtain a RMA number along with instructions for submitting your product for

service. When calling Horizon, you will be asked to provide your complete name, street

address, email address and phone number where you can be reached during business

hours. When sending product into Horizon, please include your RMA number, a list of

the included items, and a brief summary of the problem. A copy of your original sales

receipt must be included for warranty consideration. Be sure your name, address, and

RMA number are clearly written on the outside of the shipping carton.

NOTICE: do not ship Li-Po batteries to Horizon. If you have any issue with a

Li-Po battery, please contact the appropriate Horizon Product Support office.

Warranty Requirements - for Warranty consideration, you must include your

original sales receipt verifying the proof-of-purchase date. Provided warranty

conditions have been met, your Product will be serviced or replaced free of charge.

Service or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service - Should your service not be covered by warranty,

service will be completed and payment will be required without notification

or estimate of the expense unless the expense exceeds 50% of the retail

purchase cost. By submitting the item for service you are agreeing to payment of the

service without notification. Service estimates are available upon request. You must

include this request with your item submitted for service. Non-warranty service es-

timates will be billed a minimum of ½ hour of labor. In addition you will be billed for