Hifonics MT OLYMPUS CYCLOPS 3K Product Manual - Page 4
Browse online or download pdf Product Manual for Amplifier Hifonics MT OLYMPUS CYCLOPS 3K. Hifonics MT OLYMPUS CYCLOPS 3K 13 pages. Mt olympus
Print Page
6
b. aMPLIfIer feature DeSCrIPtIONS
Mt. OLYMPuS aMPLIfIerS
Mt. Olympus is a unique series of amplifiers regarding channel stability and design.
NOte:
THIS MANUAL FEATURES THE AMPLIFIERS ODIN 2K AND CYCLOPS 3K ONLY
The COLOSSUS and COLOSSUS PRO are stable at 4/2/1-Ohm per channel and 4/2-Ohms bridged.
»
»
The BOLTAR and JUPITER are stable at 4/2-Ohms per channel and 4-Ohms bridged.
»
The HERCULES and ATLAS is stable at 4/2/1-Ohm.
the ODIN 2K and CYCLOPS 3K are stable at 4/2/1-Ohm.
»
The input sensitivities for rated output powers are variable from 0.2V to 9V.
»
»
All crossovers are fully variable in their respective ranges.
»
Crossover filters are 12dB/Octave.
A green POWer LED indicates the powered up and turned on condition.
»
All HIFONICS amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,
»
and amplifier DC faults indicated by the red "PrOteCt" LED.
CautION:
DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. THIS
WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE
WARRANTY PRINTED IN THIS MANUAL.
featureS fOr ODIN 2K & CYCLOPS 3K
INPUT
OUTPUT
LEVEL
PHASE
BOOST
WIDTH
L
L
9V
0.2V
0
180
0
10dB
BASS EQ
R
R
Designed and Engineered in the U.S.A.
These amplifiers feature two DIAGNOSTIC LED's. One monitors Short Circuits and Thermal Protection while
the second monitors Clipping status.
»
INPut: RCA Inputs receives signal from the source unit.
POWER INPUT
+12V
GND
OutPut: Passes full range signal through the amplifier unchanged by settings on the amplifier. Use
»
these set of RCA's to reduce the need for muliple runs of cable to the amplifier installation location.
LeVeL: This is the input level used to balance the amplifier with the voltage from the source unit.
»
Voltage is variable from 0.2V to 9V.
»
PHaSe: Variable time alignment from 0 to 180 degrees.
baSS eQ: ParaMetrIC
»
•
bOOSt: 0 to +10dB. Will enhance bass the FREQUENCY selected.
•
WIDtH: Narrow to Wide range enhancements above and below the center FREQUENCY.
GND
REM
+12V
•
CeNter: Variable center frequency from 30Hz to 100Hz.
reMOte: Plug in the bass remote to this port.
»
POWER
INPUT
SubSONIC fILter: Low frequency cutoff variable from 15Hz to 35Hz.
»
LOW PaSS fILter: High frequency cutoff variable from 35Hz to 250Hz.
»
»
MODe: (ODIN 2K & CYCLOPS 3K):
•
MSt (MASTER): Factory setting for the switch location when using the amp alone is always set to
MST. Also used when linking a pair of either the ODIN 2K or CYCLOPS 3K amplifiers. When in MST
position, a single RCA can be connected to the MASTER OUT RCA receptacle to provide signal to
the SLAVE INPUT on the SLAVE amplifier.
•
SLV (SLAVE): Your MODE switch should only be in this position if you are linking a pair of ODIN
2K or CYCLOPS 3K amplifiers and one of them will be the SLAVE. At that point the SLAVE amp will
receive the single RCA on the SLAVE IN. No other RCA's can be connected to your amplifier other
than SLAVE IN when in SLAVE IN position.
PrOteCt & POWer: These indictors tell you the status of the amplifier.
»
MASTER
REMOTE
PROTECT
CENTER
SUBSONIC
LPF
MODE
OUT
MST
SLV
30 100Hz
15
35Hz
35
250Hz
POWER
SLAVE IN
SEE OWNERS MANUAL
FOR DIAGNOSTIC CODES
SPEAKER OUTPUT
REM
FUSE
50
50
SPEAKER
OUTPUT
7