Autonics KRN1000 Series Instruction Manual

Browse online or download pdf Instruction Manual for Measuring Instruments Autonics KRN1000 Series. Autonics KRN1000 Series 2 pages. Lcd touchscreen paperless recorder
Also for Autonics KRN1000 Series: User Manual (15 pages), Instruction Manual (2 pages)

Print Page

Autonics KRN1000 Series Instruction Manual

AEP-E-0180C

LCD Touchscreen Paperless Recorder

KRN1000 SERIES

I N S T R U C T I O N

M A N U A L

Thank you for choosing our Autonics product.

Please read the following safety considerations before use.

Safety Considerations

※Please observe all safety considerations for safe and proper product operation to avoid hazards.

※Safety considerations are categorized as follows.

Warning

Failure to follow these instructions may result in serious injury or death.

Caution

Failure to follow these instructions may result in personal injury or product damage.

※The symbols used on the product and instruction manual represent the following

symbol represents caution due to special circumstances in which hazards may occur.

Warning

1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or substantial economic

loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety

equipment, crime/disaster prevention devices, etc.)

Failure to follow this instruction may result in personal injury, fire, or economic loss.

2. The unit must be installed on a device panel before use.

Failure to follow this instruction may result in electric shock.

3. Do not connect, repair, or inspect the unit while connected to a power source.

Failure to follow this instruction may result in electric shock .

4. Do not disassemble or modify the unit. Please contact us if necessary.

Failure to follow this instruction may result in electric shock or fire.

5. Check the terminal numbers before connecting the power source.

Failure to follow this instruction may result in fire or burning the unit.

Caution

1. Do not use the unit outdoors.

Failure to follow this instruction may result in shortening the life cycle of the unit, or electric shock.

2. Use the unit within the rated specifications.

Failure to follow this instruction may result in shortening the life cycle of the unit, or fire.

3. Do not use water or oil-based detergent when cleaning the unit. Use dry cloth to clean the unit.

Failure to follow this instruction may result in electric shock or fire.

4. Do not use the unit where flammable or explosive gas, humidity, direct sunlight, radiant heat, vibration, or impact may be

present.

Failure to follow this instruction may result in fire or explosion.

5. Keep dust and wire residue from flowing into the unit.

Failure to follow this instruction may result in fire or product damage.

6. Check the polarity of the power contact before wiring the unit.

Failure to follow this instruction may result in fire or explosion.

※Please read "Safety Considerations" in KRN1000 user manual before using.

Ordering Information

KRN1000

Case

Standard panel installation type

Power supply

100-240VAC 50/60Hz

Communication output

RS422/485+Ethernet+USB Device

None

Alarm relay output 8 channels

Alarm relay output 6 channels + Digital input 2 channels

Option input/output

Alarm relay output 6 channels

+ 24VDC power output for transmitter

Alarm relay output 4 channels + Digital input 2 channels

+ 24VDC power output for transmitter

4 channels

Input channels

8 channels

12 channels

16 channels

Item

KRN1000 Paperless recorder

User Manual

For the detail information and instructions, please refer to user manual and user manual for communication.

Download manuals from the enclosed CD-ROM or our web site (www.autonics.com).

※The above specifications are subject to change and some models may be discontinued without notice.

Specifications

Series

KRN1000

Power supply

100-240VAC 50/60Hz

Allowable voltage range

85 to 110% of rated voltage

Power consumption

Max. 23VA

Display method

5.6 inch TFT Color LCD

Resolution

640×480 pixels

Screen

Adjusting brightness

3-level (Min/Standard/Max)

Input method

Touch screen (Pressure sensitive type)

Number of input channels

4 / 8 / 12 / 16 channels

※1

Universal input

Temperature sensors (thermocouple, RTD), Analog (voltage, current (shunt))

1 to 4-CH: 25ms/125ms/250ms, 5 to 16-CH: 125ms/250ms

Sampling period

(internal sampling period is average movement filter and alarm output operation unit time)

Recording period

1 to 3600 sec

Internal memory

Approx. 200MB

External memory

SD / USB memory max. 32GB

2300VAC 50/60Hz for 1 min (between power terminals and case)

Dielectric strength

※Except ethernet and USB device

Mechanical

10 to 60Hz 4.9m/s

in each X, Y, Z direction for 1 hour

Vibration

Malfunction

10 to 60Hz 1m/s

in each X, Y, Z direction for 10 min

Insulation resistance

Over 20MΩ (at 500VDC megger)

Noise immunity

Square shaped noise by noise simulator (pulse width 1µs) ±2kV

Time accuracy

Within ±2 min/year (available up to 2099)

Protection structure

IP50 (front part)

Ambient temperature

0 to 50℃, storage: -20 to 60℃

Environ-

ment

Ambient humidity

35 to 85%RH, storage: 35 to 85%RH

Approval

Weight

※2

Approx. 1290 to 1400g (approx. 590 to 700g)

※1: For more information of universal input, refer to '

Input/Output'.

※2: The weight includes packaing. The weight in parenthesis is for unit only.

※Environment resistance is rated at no freezing or condensation.

Unit Description

Front part

1. Power indicator: Power turns ON and the red LED turns ON.

2. Screen: Measrued value is displayed as trand graph, bar bar graph,

digital figures.

3. Front cover: Open the front cover. There are power switch and, USB

Host/Device, SD card slot.

4. Power switch: Turn ON/OFF the power of KRN1000.

5. USB host port: Connect the USB memory.

It recognizes up to 32GB. When using extension cable,

cable length should be up to 1.5m.

6. USB device port: Used for parameter settings.

7. SD card slot: SD card memory slot. It supports up to 32GB.

8. Stylus pen: Used for touching screen.

※Do not connect the other USB devices except USB memory at USB host

port.

Rear part

1. Sensor input terminal: Connects universal input.

2. Ethernet port: Connector for ethernet cable.

It communicates Modbus TCP.

3. RS422/485 port: Connects RS422/485 for Modbus RTU communication.

4. Option input/output port: Connects for option input/output (digital

5. Power input: Power connection (100-240VAC 50/60Hz)

Dimensions

144

11.5

● Bracket

69.2

Input/Output

Type

Input/Output type

Input type

Universal input

Input impedance

Display

accuracy

Resolution

Digital

input

Option

Alarm relay

input/output

※3

output

Power output for transmitter

RS422/485

Communication

Ethernet

output

※5

USB Device

※1: Current measurement and connection examples

Connect 250Ω shunt resistance and set analog input type 0-20mA (shunt) / 4-20mA (shunt).

It is available to measure 0-20mA / 4-20mA current.

※2:

At room temperature (23℃ ± 5℃)

RTD Cu50Ω (-200≤T≤200): (±0.1% F.S. or ±1.5℃, select the higher one) ±1-digit

RTD DPt50Ω (-200≤T≤500): (±0.1% F.S. or ±1.5℃, select the higher one) ±1-digit

Thermocouple R, S, C, G type (0≤T≤100): (±0.1% F.S. or ±4.0℃, select the higher one) ±1-digit

Thermocouple U, T type (-100≤T≤400): (±0.1% F.S. or ±2.0℃, select the higher one) ±1 digit

Thermocouple B type, below 400℃: There is no accuracy standards.

All thermocouples, below -100℃: (±0.3% F.S. or ±4.0℃, select the higher one) ±1-digit

Out of room temperature range

RTD Cu50Ω (-200≤T≤200): (±0.2% F.S. or ±3.0℃, select the higher one) ±1-digit

RTD DPt50Ω (-200≤T≤500): (±0.2% F.S. or ±3.0℃, select the higher one) ±1-digit

※3: Input/Output is different by option. Refer to '

※4: For supplying power for transmitter, it is recommened to use shield cable to reduce noise.

※5: RS422/485, ethernet, USB device communication outputs are not used at the same time.

※If sensor input line is longer, it is recommended to use shield cable to reduce noise.

Input/Output Circuit

Universal input

Option input/output 1

(alarm output 8 channels)

Option input/output 3

(alarm output 6 channels + power for transmitter output)

input (non-contact/ contact), alarm output,

power for transmitter).

Comprehensive Device Management Program [DAQMaster]

DAQMaster is the comprehensive device management software for setting parameters and monitoring processes.

DAQMaster can be downloaded from our web site at www.autonics.com.

Item

Minimum specifications

System

IBM PC compatible computer with Pentium Ⅲ or above Hard disk

Operations Windows 98/NT/XP/Vista/7/8/10

Memory

256MB+

(unit: mm)

Error Message

● Panel cut-out

Min. 175

Error message

Descriptions

When input type is temperature sensor (Thermocouple, RTD) and the measurement value is higher than high-limit value of input

range, it flashes HHHH. It is cleared when the measurement value is within the high-limit range.

HHHH

When input type is analog (voltage, current (shunt)) and the measurement value is over 10% of high-limit input range, it flashes

HHHH. It is cleared when the measurement value is within 10% of high-limit input range.

When input type is temperature sensor (Thermocouple, RTD) and the measurement value is lower than low-limit value of input

range, it flashes LLLL. It is cleared when the measurement value is within the low-limit range.

LLLL

When input type is analog (voltage, current (shunt)) and the measurement value is over 10% of low-limit input range, it flashes

138

+1.0

LLLL. It is cleared when the measurement value is within 10% of low-limit input range.

When input type is temperature sensor (Thermocouple, RTD) and input is break, it flashes BURN.

BURN

It is cleared when input is connected.

When forgetting and entering unvaild password 3 times, "ASKey" appears with error message.

ASKey

Contact our service center with ASKey.

Description

RTD

JPt100Ω, DPt100Ω, DPt50Ω, Cu100Ω, Cu50Ω (supplied current: approx. 190µA)

Thermocouple

B, C (W5), E, G, J, K, L, L (Russia), N, P, R, S, T, U

Voltage: ±60mV, ±200mV, ±2V, 1-5V, ±5V, -1V-10V

Analog

Current: 0-20mA, 4-20mA (measureable when using 250Ω shunt resistance)

Voltage (V): Approx. 205kΩ

RTD, Thermocouple, Voltage (mV): Min. 200kΩ

RTD

Warm-up time: Max. 30 min

Thermocouple

At room temperature (25±5℃): ±0.1% F.S.±1-digit

※2

Out of room temperature: ±0.2% F.S.±1-digit

Analog

16-bit

No-contact input

ON: Residual voltage max. 1V, OFF: Leakage current max. 0.1mA

Contact input

ON: Max. 1kΩ, OFF: Min. 100kΩ, Short-circuit: Approx. 4mA

Capacity

250VAC 3A, 30VDC 3A, 1 Form A (resistive load)

Mechanical: Min. 20,000,000 operations

Life cycle

Electrical: 100,000 operations (3A 250V AC, 3A 30V DC)

24±2VDC, Max. 60mA ※Built-in over current protection circuit

※4

Modbus RTU ※It is recommended to use shielded cable over AWG 24.

IEEE802.3 10 BASE-T / IEEE802.3U 100 BASE-TX (Modbus TCP)

USB V2.0 Full Speed (Modbus RTU)

Ordering Information'.

Communication output

Option input/output 2

(alarm output 6 channels + digital input 2 channels)

Option input/output 4

(alarm output 4 channels + digital input 2 channels

+ power for transmitter output)

Item

Minimum specifications

1GB+ of available hard disk space

VGA

Resolution: 1024×768 or higher

Others

RS232C serial port (9-pin), USB port

※1