Activox LifeChoice XYC105B Operator's Manual - Page 5

Browse online or download pdf Operator's Manual for Medical Equipment Activox LifeChoice XYC105B. Activox LifeChoice XYC105B 16 pages. Lifechoice activox portable oxygen concentrator

Print Page

USER CONTROLS

The user controls on the LifeChoice Activox POC are specifically

designed to be pressed by a finger. Never press any of the buttons

with a pen, screwdriver, stylus or any other object. Pressing the buttons

with any hard, sharp and/or small object can damage the user controls

and void all warranties. The following items are essential parts of the

user controls for the LifeChoice Activox POC:

Pulse Setting

Control Buttons

1, 2, 3 LPMeq

Power Button

Auto Mode LEDs

Mute Button

Indicator Lights: Colored LED lights indicate either a change in

operating status or a condition that may need response (alarm).

Audible Signals: An audible signal (beep) indicates either a change

in operating status or a condition that may need response (alarm).

Subjective audio response will vary among different people due to

different hearing abilities.

Power Button: To turn the LifeChoice Activox POC on or off, press the

Power Button.

Auto Mode LEDs: There are two inhalation sensitivity modes on the

control panel: Active-High and Sleep-Low, which automatically adjust

based on oxygen demand (e.g breathing patterns) requirements.

(Reference Control Panel diagram.)

Mute Button: The LifeChoice Activox POC features a mute function to

disable audible alarms during operation. If an alarm has been muted,

the amber Mute Button LED will be illuminated. (Reference Control

Panel diagram.) Please use this function appropriately since it silences

information about the health condition of the device (important audio

signals).

INT and EXT LED: These LED lights will indicate which power

source the unit is using or charging. The INT LED represents the

internal battery, while the EXT LED represents the external battery.

Control Panel

Battery Charge

Indicator

Alarm Indicator

Hour Meter

Button

For use by trained

INT & EXT

Battery Check

service personnel

Indicator

Button

only

Battery Check Button: The Battery Check Button causes the corre-

sponding battery charge level (e.g. internal or external battery) to be

displayed. (Reference Control Panel diagram.)

Battery Charge Indicator: The Battery Charge Indicator consists of

four LEDs labeled "25%", "50%", "75%", and "100%". (Reference

Control Panel diagram.) Charge-level indication is approximate

except at full charge when all four LEDs are solid green. Use the

following examples to interpret other charge levels:

Charge Level

25% LED

50% LED

>0% and <13%

Flashing Green

>13% and

Solid Green

< 26%

>26% and

Solid Green

Flashing Green

<37%

>37% and

Solid Green

<51%

>51% and

Solid Green

<63%

>63% and

Solid Green

<76%

>76% and

Solid Green

< 87%

>87%

Solid Green

Pulse Setting Control Buttons: There are three individual Pulse

Setting Control Buttons on the control panel: 1, 2, and 3 which are pulse

equivalent to 1, 2, or 3 liters per minute (LPMeq) settings on a

continuous flow device. (Reference Control Panel diagram.)

Hour Meter Button: The LifeChoice Activox POC will read and

display the number of hours that the unit has been used. (Refer to

Routine Maintenance section.)

Nasal Cannula: A standard single lumen nasal cannula or equivalent

must be used with the LifeChoice Activox POC to provide oxygen from

the concentrator. A standard single lumen type cannula, 7-foot

(2-meter), is recommended for use. An Adult Nasal Cannula like

#1107 by Ventlab Corporation is supplied with each LifeChoice

Activox POC.* For replacement cannulas, please contact your local

medical equipment supplier. Follow cleaning and care instructions

provided with the nasal cannula.

CAUTION: Use of some administration accessories not specified for

use with this oxygen concentrator may impair the performance.

*Nasal cannula may not be included in XYC100B package in all countries based on local in-

ternational requirements.

75% LED

100% LED

Off

Flashing Green

Off

Solid Green

Off

Solid Green

Flashing Green

Solid Green