dynarex DynaRide 10236 Manual - Page 2
Browse online or download pdf Manual for Wheelchair dynarex DynaRide 10236. dynarex DynaRide 10236 2 pages.
Print Page
USE AND SAFETY
TO OPEN CHAIR
Open wheelchair by tilting to
one side and pushing down on
seat rail until fully opened.
TO CLOSE CHAIR
First fold foot plates to vertical
position. Grab seat with both
hands at front and back edge and
lift. Or, tilt chair to one side and lift
up on seat rail.
BACK WHEELS
Large rear wheels should be inspected
at least once a month to ensure proper tightness. If wheel
wobbles or is loose, release lock nut and tighten axle bolt
slightly. Test for proper tightness by leaning chair to one
side and spin adjusted wheel.
TIRES
Solid rubber tires need minimal maintenance, but
should be cleaned occasionally with a damp cloth. Replace
if tires become severely worn or cracking appears.
WHEEL LOCKS
Engage both wheel locks before getting
in or out of chair, leaning forward in chair, or while in an
elevator or wheelchair lift. Locks
Carriage Bolt
are engaged by pushing handle
and Nut
completely forward. Adjustments
Mounting
to locks are made by loosening
Positions
or tightening nut on the carriage
bolt. Wheel lock shoe should be
embedded at least ⅛". Adjust by
sliding clamp toward rear wheel
while handle is engaged in
locked position. Tighten nut and
bolt to secure in position. Test for
correct locking action before
actual use.
FRONT CASTERS
Casters should be checked periodically
and lubricated occasionally. Lubricate by removing fork and
greasing caster stem bearings and wheel bearings.
Reassemble fork and wheel by tightening nuts until no play
remains, but wheels roll freely. If nut is too loose, caster will
shimmy, if too tight, chair will be hard to steer.
REMOVAL OF SWING-AWAY
FOOTRESTS/LEG RESTS
Release lock by pushing on
the front rigging lever.
Swing-away foot rest/leg
rest out and sideways.
Lift to remove.
ADJUSTING LENGTH OF
FOOTREST/LEG REST
When adjusting length of
footrests or leg rests, user
should be sitting in wheelchair
with feet on the foot plates.
Loosen cam lock lever around
support assembly and push the
release button. Raise or lower
foot plate to desired position that
will provide maximum support of
thighs. Ensure release button is
fully engaged, tighten cam lock lever. Front rigging should
not be so low that it causes uncomfortable pressure to
thighs at front of seat upholstery.
ADJUSTING/ELEVATING LEG REST
Lift foot plate on leg rest assembly
to desired position. Release leg rest
Handle
assembly and it will automatically
lock into place. To lower, push the
release lever and lower foot plate
to desired position.
GENERAL CARE
Wheel Lock
cloth at least once a week. All metal parts can be cleaned
with auto wax or similar products. If exposed to moisture,
Wheel Lock
Shoe
dry immediately. Do not use an abrasive cleanser that will
scratch the finish.
Rear Wheel
REMOVABLE ARMS
button and lifting arms out of front and rear sockets.
Front Rigging
Release Lever
Front Rigging
Assembly
Hinge
Pins
Footplate
Hinge
Plates
Front Rigging
Support
Release
Button
Footplate
Adjustment
Assembly
Holes
Cam Lock
Lever
Hinge
Plate
Release Lever
Wipe chrome parts with a clean, soft
Remove arms by depressing spring
WARNING
Do not adjust or operate wheelchair without carefully
Reorder Nos. 10242
reading all instructions in this manual.
10243
Do not operate this wheelchair on roadways, streets or any
10244
surfaces with vehicular traffic.
Do not operate on inclines without proper assistance.
When getting in and out of wheelchair or when in elevator or
wheelchair lift, wheel locks must be fully engaged.
Wheelchair should be on a smooth, stable and level area
with wheel locks engaged before transferring user in or out
of wheelchair.
Footrest should not be lower than 2½" from the ground to
ensure clearance.
Do not stand on or apply weight to foot rests.
Rotate casters to front of the wheelchair and engage wheel
locks to help prevent wheelchair from tipping over before
reaching or leaning forward.
When trying to extend arms over back, only reach as far as
your arm can extend without having to alter your seating
position. Do not lean over or apply weight to the top of
wheelchair back. This can cause wheelchair to tip over.
DO NOT stand on wheelchair.