Autopage RST-1100 Owner's Manual - Page 15

Browse online or download pdf Owner's Manual for Remote Starter Autopage RST-1100. Autopage RST-1100 20 pages. Remote engine starter with alarm system

Print Page

NOISE ABATEMENT CIRCUIT: Your system has "Noise Abatement Circuit". It can prevent annoying

repetitive trigger sequences due to faulty door pin switches or environmental condition such as thunder,

jackhammers, airport noise, etc.

Here's how the "Noise Abatement Circuit" works: If the alarm triggers five times, each time the same

sensor (zone 4) is triggered the "Noise Abatement Circuit" will interpret this pattern of triggers as false

alarms. After the fifth trigger, the "Noise Abatement Circuit" ignores, or bypasses that sensor until any other

sensor or switch is triggered.

"Noise Abatement Circuit" covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door

for six full cycles, the doors will be bypassed until the trigger ceases.

M. ANTI CAR- JACKING

Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature

"OFF". This system is default setting all car-jacking "OFF".

ACTIVE ANTI CAR JACKING:

1. Spin up the

switch to the page

button for 2 seconds or press and hold the transmitter

same time for 2 seconds while the vehicle's ignition is ON. The parking lights will

turn on for 1.5 seconds to indicate the system has entered the car-jacking mode.

2. Once the system is in car-jacking mode and you are forced from the vehicle, the

system will be triggered when the door is opened and closed while the ignition is in

the "ON" position.

PASSIVE ANTI CAR- JACKING:

1. Turn the ignition switch to the "ON" position. The system enters the car-jacking

mode.

2. Once the system is in car-jacking mode and you are forced from the vehicle, the

system will trigger when the door is opened and closed while the ignition is in the

"ON" position.

TRIGGER THE ANTI CAR -JACKING MODE:

a). 50 seconds after the system has beer triggered. The siren will start chirping for 15 seconds.

b). During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off

the car-jacking feature. If not, it will enter second timer car jacking.

c). 65 seconds after the system has beer triggered. The siren starts alarming and the parking light starts

flashing. (Forced engine shutdown mode is activated (if installed), the vehicle will slowly shutdown

within 25 seconds.)

d). 90 seconds after the system has beer triggered

1. The siren still alarming and the parking light flashing, and

2. The starter disable will activate to prevent the vehicle from starting.

3. It will remain active until the vehicle's battery power exhausted.

OVERRIDE THE SYSTEM TO TURN OFF ANTI CAR- JACKING:

Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and

the system disarmed

Note: If you use password pin code to double protect the vehicle security, you will need to use it to

completely disarm the system.

N. SYSTEM'S TRIGGER CHECK

Spin up the

switch to the page

Check" button. The remote will respond with one melody sound

and all trigger records will immediately be displayed on the OLED

screen.

Note: It will display the homepage if there were no system's

triggered.

O. SYSTEM'S STATUS CHECK

Spin up the

switch to the page

Check" button. The remote will respond with one melody sound

and the vehicles status will immediately be displayed on the OLED

screen.

Note: It will display the home page if the car's status is normal.

P. DRIVER PAGING / LOSE & FOUND

It is useful the event that someone wants to page the driver of the parked vehicle or someone cannot find

his OLED remote transceiver.

RST1000 OP REV.A

and then press and hold the "Car Jacking"

(Programmable)

and then press the "Trigger

and then press the "Status

and

buttons at the

Jun/22/2009